mimms2
Banned

1231 Likes

Page 13 of 83 First 12345678910111213141516171819202122232425262763 ... Last

• Jump to page:

1. 
   mimms2 liked post by tetawa On thread : Rounds jamming into lands

   When I FLR a belted case, wind the die back 3 or 4 turns, then resize and slowly wind forward and resize again until the bolt closes with slight resistance.

   Liked On: 15-09-2021, 06:57 PM

2. 
   mimms2 liked post by T.FOYE On thread : Rounds jamming into lands

   What i see is the lack of cut marks. I think you have a carbon ring that has formed in your chamber throat. When i deliberately extend my projectile fwd i always see little razor like cuts which i...

   Liked On: 15-09-2021, 06:54 PM

3. 
   mimms2 liked post by grandpamac On thread : Rounds jamming into lands

   Greetings kayneb, I think that vietnamcam has cracked it. Generally neck dies are set up to size no more than 80% of the neck to ensure that the shoulder is not bulged by die contact as vietnamcam...

   Liked On: 15-09-2021, 06:52 PM

4. 
   mimms2 liked post by Ftx325 On thread : Ruger 450 Bushmaster ???

   if you're going to do something you may as well do it properly .... 45/70 ;)

   Liked On: 15-09-2021, 06:44 PM

5. 
   mimms2 liked post by Seventy Six On thread : Rounds jamming into lands

   Usually you can only neck size a certain number of times before chambering and extraction becomes sticky and then you have to full size, hence why neck sizing has fallen out of favour these days. ...

   Liked On: 15-09-2021, 06:44 PM

6. 
   mimms2 liked post by kayneb On thread : Rounds jamming into lands

   Na no signs of pressure and were 2grns lower than max load in hornady manual. rounds were tight to chamber and leaving rifling marks on the projectiles. Rifle is a fierce 24inch 7mmRM, rounds are...

   Liked On: 14-09-2021, 09:15 PM

7. 
   mimms2 liked post by veitnamcam On thread : Rounds jamming into lands

   What is your indicaction they were jamming into lands? did you stick a round in the chamber and try to eject a live round and have the bullet stick in the barrel? Your lands dont move back and...

   Liked On: 14-09-2021, 09:13 PM

8. 
   mimms2 liked post by erniec On thread : Best Offroad Aerial and Radio

   Will look at them. The one that has been on it for years just has a wire type one. Broke on down south got some brazing rod from the local garage unit I could get a replacement. Cant rush these...

   Liked On: 14-09-2021, 08:31 PM

9. 
   mimms2 liked post by madmaori On thread : Mazda Marvie/Proceed

   I had one of these , biggest heap of shit I have ever owned! thirsty , gutless , shit ground clearance and quite long so it was extremely poor off-road. Keep looking boss.......just not at these haha

   Liked On: 14-09-2021, 07:52 PM

10. 
    mimms2 liked post by MSL On thread : Mercedes ML270

    It’s not a truck Sent from my iPhone using Tapatalk

    Liked On: 14-09-2021, 07:33 PM

11. 
    mimms2 liked post by Micky Duck On thread : Is threading a Savage 99 for a suppressor sacrilege?

    you could take off origonal barrel...put it in grease and chop replacement barrel to your hearts content...you get to keep origonal barrel in case you want to restore it back again...and use it...

    Liked On: 13-09-2021, 09:44 PM

12. 
    mimms2 liked post by S.E.G On thread : AP70N and dacron

    Don’t bother with the Dacron, just load, shoot and repeat as needed. Also check out https://castboolits.gunloads.com

    Liked On: 13-09-2021, 08:44 PM

13. 
    mimms2 liked post by Tentman On thread : Is threading a Savage 99 for a suppressor sacrilege?

    Its yours, do whatever suits you, I'm not a great suppressor fan but I've threaded/otherwise modified rifles that would make others scream - I just say "well that makes the rest of them more...

    Liked On: 13-09-2021, 11:47 AM

14. 
    mimms2 liked post by 7mmsaum On thread : 22 Ammo ES and SD for longer range

    CCI standard (1070 FPS) solid nose is making 100-150 mm groups for me at 200 metres Tikka T1X 16 inch

    Liked On: 12-09-2021, 04:10 AM

15. 
    mimms2 liked post by ebf On thread : Leupold CDS set/grub screw size

    Grub screw spec is 4-40, it is 1/4 (0.250) inch long. You need a 3/64 hex allen key, in a pinch a 1.0mm metric allen key will work as well.

    Liked On: 11-09-2021, 10:22 PM

Page 13 of 83 First 12345678910111213141516171819202122232425262763 ... Last

• Jump to page: