mimms2
Banned

1231 Likes

Page 69 of 83 First ... 195556575859606162636465666768697071727374757677787980818283 Last

• Jump to page:

1. 
   mimms2 liked post by MSL On thread : Marlin 30-30 setup

   The crimp is to prevent the projectiles from being pushed into the case by the base of the next round when in the mag tube. Sent from my iPhone using Tapatalk

   Liked On: 22-04-2020, 03:31 PM

2. 
   mimms2 liked post by Chazzwazzer On thread : feral cats war in Oz

   Cats (feral and domestic) are 100% responsible for the extinction of a number of reptile/amphibian and mammal species in Australia and threaten dozens more. That cats are allowed to roam outside is...

   Liked On: 20-04-2020, 08:11 PM

3. 
   mimms2 liked post by Bol Tackshin On thread : T/CR22 bolt hold open... why?

   If you don't like to be hold open on the last shot with the TCR, use Ruger magazines. I believe it only works with the TC mags. And they have an integral weaver rail, which in my mind makes them a...

   Liked On: 20-04-2020, 04:31 PM

4. 
   mimms2 liked post by PaulNZ On thread : T/CR22 bolt hold open... why?

   That doesn't seem quite right - how could there be a slot cut in the barrel for the firing pin? Setting off the round requires support of the case rim under the firing pin - a slot would seem to be...

   Liked On: 20-04-2020, 04:31 PM

5. 
   mimms2 liked post by Marty Henry On thread : Additional baffles and impact on accuracy

   Fitting a suppressor will alter your point of impact as you are hanging a weight off the end of the barrel that will alter it's vibration frequency, think of it as sort of a barrel tuner. Many people...

   Liked On: 20-04-2020, 09:19 AM

6. 
   mimms2 liked post by Chilli_Dog On thread : Machining Needed - UHMWPE Polymer Stock / Chassis

   You wont find much that is worse than uhmwpe for thermal expansion either. I wonder how a composite/sheet metal design would go

   Liked On: 20-04-2020, 09:11 AM

7. 
   mimms2 liked post by Bol Tackshin On thread : Barrel Fluting - existing barrel

   From the little I read up on the subject, it is most important to ensure the bore is central to the barrel along its whole length the barrel walls must be equally thick on every radius at any given...

   Liked On: 18-04-2020, 08:40 PM

8. 
   mimms2 liked post by Micky Duck On thread : .17hmr vs .22lr vs .223 BEST FARM GUN?

   every man should own a .22lr that said I shoot more bunnies n hares with the .223 BUT I arent in populated area....hares and rabbits out to 75-80 yards no issues and if you work out your drop...

   Liked On: 17-04-2020, 08:48 AM

9. 
   mimms2 liked post by bully On thread : .17hmr vs .22lr vs .223 BEST FARM GUN?

   .17 the better .22 17 good if your eating the critters. 22 best for shooting possums up trees, wont go so far. other than that 223 trumps all, especially in open ground and wind, longer...

   Liked On: 17-04-2020, 08:48 AM

10. 
    mimms2 liked post by 7mmsaum On thread : .17hmr vs .22lr vs .223 BEST FARM GUN?

    Get one of each They all have their uses

    Liked On: 16-04-2020, 09:56 PM

11. 
    mimms2 liked post by Yesmate On thread : No hunting under level 3

    This is BS,hunting poses no extra risk of spending the virus and far less risk of putting extra load emergency/health system than the construction industry re starting. look at the data for...

    Liked On: 16-04-2020, 05:41 PM

12. 
    mimms2 liked post by Moutere On thread : Suppressor for a .22Mag

    It's likely just the sonic crack, can't do anything in terms of suppressing that.

    Liked On: 16-04-2020, 11:05 AM

13. 
    mimms2 liked post by rugerman On thread : Photos of your dog

    Sorry to hear about your bitch mimms, it's never a happy time when they go. Good luck with the new one. Your right letting her eat till she pukes wont do anything, since dogs have such a well...

    Liked On: 15-04-2020, 12:30 PM

14. 
    mimms2 liked post by chalkeye On thread : New stock

    Haven't posted in a while. Been working on an updated stock design for ages, finally got my ducks lined up to make another prototype. I bought a used CNC router off a farmer in Gore for a steal and...

    Liked On: 15-04-2020, 08:45 AM

15. 
    mimms2 liked post by timattalon On thread : New stock

    I do not know what you do for a job, but if you get the practise in, Boyds / GRS etc may be in trouble. Something like that could be worth buying local if you were able Looks great. Very well done.

    Liked On: 15-04-2020, 08:44 AM

Page 69 of 83 First ... 195556575859606162636465666768697071727374757677787980818283 Last

• Jump to page: