No.3
Member

2664 Likes

Page 8 of 178 First 1234567891011121314151617181920212258108 ... Last

• Jump to page:

1. 
   F Majeur liked post by No.3 On thread : Accuracy troubleshooting suggestions?

   Reduction in felt recoil can lower the point of impact by reducing muzzle flip - could be a large part of a 'miss low' at longer range. Need to recheck zero with the new muzzle attachment to know...

   Liked On: 18-04-2025, 08:56 AM

2. 
   TimC liked post by No.3 On thread : DPT muzzle break end cap results.

   Would be interesting to shoot a group unsuppressed - just cause, scientific reasons etc etc.

   Liked On: 17-04-2025, 08:48 PM

3. 
   Micky Duck liked post by No.3 On thread : HIGHWAY AMIMALS

   Mate came up on the ferry one night, arrived back home near Aucks early in the morning and went to bed. Woke up about midday and couldn't figure out what the stench was outside the house... Had...

   Liked On: 17-04-2025, 04:59 PM

4. 
   Deanohit liked post by No.3 On thread : Excavators

   45 years old? Just run in!

   Liked On: 16-04-2025, 10:15 PM

5. 
   300Shortmag liked post by No.3 On thread : Magnum or large rifle primers in 7saum

   I'd start with LR standard and only go up if you can't find a load that works for whatever reason. My feeling is the older style heavily retardant coated ball powders that really did need magnum...

   Liked On: 16-04-2025, 08:54 PM

6. 
   XR500 liked post by No.3 On thread : Excavators

   45 years old? Just run in!

   Liked On: 16-04-2025, 08:37 PM

7. 
   trapperjohn liked post by No.3 On thread : Excavators

   I have talked to guys that brought brand new gear from China and by the time they have gone through and replaced all the hydraulic hoses, changed and serviced the hydraulic setup a couple of times to...

   Liked On: 16-04-2025, 07:18 PM

8. 
   XR500 liked post by No.3 On thread : Excavators

   I have talked to guys that brought brand new gear from China and by the time they have gone through and replaced all the hydraulic hoses, changed and serviced the hydraulic setup a couple of times to...

   Liked On: 16-04-2025, 06:43 PM

9. 
   Dan88 liked post by No.3 On thread : Excavators

   It will fit. I can guarantee it 100%. It's a digger after all. Now please note that as a result of that comment I am not volunteering my time as a fence and gate repairer!

   Liked On: 16-04-2025, 12:04 PM

10. 
    XR500 liked post by No.3 On thread : Excavators

    It will fit. I can guarantee it 100%. It's a digger after all. Now please note that as a result of that comment I am not volunteering my time as a fence and gate repairer!

    Liked On: 16-04-2025, 10:48 AM

11. 
    Localman liked post by No.3 On thread : Excavators

    It will fit. I can guarantee it 100%. It's a digger after all. Now please note that as a result of that comment I am not volunteering my time as a fence and gate repairer!

    Liked On: 16-04-2025, 10:01 AM

12. 
    XR500 liked post by No.3 On thread : Excavators

    The other thing to be looking for apart from track gear, slew rings and the other obvious wear points is seeing if you can find the type of work it was used for - one machine I saw spent a...

    Liked On: 15-04-2025, 11:12 AM

13. 
    Woody liked post by No.3 On thread : Why the FSA advice against using FAL as ID

    Almost - it is based on what the person who enters it into the records typed. There are quite a few people who get a certed copy of their birth cert later in life and find they've been spelling...

    Liked On: 15-04-2025, 08:36 AM

14. 
    XR500 liked post by No.3 On thread : Excavators

    Was just going to suggest that same thing, 20 ton once you have it on site...

    Liked On: 15-04-2025, 08:03 AM

15. 
    Deanohit liked post by No.3 On thread : Why the FSA advice against using FAL as ID

    I have used the FAL several times, people get a little stupid about ID and what they will "accept" but there are many forms of photo ID that satisfy the requirements. Govt issued professional body...

    Liked On: 14-04-2025, 02:42 PM

Page 8 of 178 First 1234567891011121314151617181920212258108 ... Last

• Jump to page: