NO4
Member

162 Likes

Page 2 of 11 First 1234567891011 Last

• Jump to page:

1. 
   shananah liked post by NO4 On thread : 26mm Rings?

   couldn't you use 1" rings and run a adjustable hand reamer through them?

   Liked On: 23-07-2023, 08:58 PM

2. 
   erniec liked post by NO4 On thread : Mini excavator centre pivot/swivel help

   I deal with hydraulic rams, rotators, motors and pumps everyday. Orings are measured from there ID with sections of 1/16(1.78mm), 3/32(2.62mm), 1/8(3.53mm),3/16(5.33mm) and 1/4(6.99mm) you can get...

   Liked On: 19-07-2023, 04:45 PM

3. 
   Billbob liked post by NO4 On thread : Mini excavator centre pivot/swivel help

   I deal with hydraulic rams, rotators, motors and pumps everyday. Orings are measured from there ID with sections of 1/16(1.78mm), 3/32(2.62mm), 1/8(3.53mm),3/16(5.33mm) and 1/4(6.99mm) you can get...

   Liked On: 18-07-2023, 10:51 PM

4. 
   Tentman liked post by NO4 On thread : Mini excavator centre pivot/swivel help

   I deal with hydraulic rams, rotators, motors and pumps everyday. Orings are measured from there ID with sections of 1/16(1.78mm), 3/32(2.62mm), 1/8(3.53mm),3/16(5.33mm) and 1/4(6.99mm) you can get...

   Liked On: 18-07-2023, 10:25 PM

5. 
   ishoot10s liked post by NO4 On thread : Mini excavator centre pivot/swivel help

   I deal with hydraulic rams, rotators, motors and pumps everyday. Orings are measured from there ID with sections of 1/16(1.78mm), 3/32(2.62mm), 1/8(3.53mm),3/16(5.33mm) and 1/4(6.99mm) you can get...

   Liked On: 18-07-2023, 10:08 PM

6. 
   ishoot10s liked post by NO4 On thread : Mini excavator centre pivot/swivel help

   use a set of internal calipers to measure your groove diameter set to id then measure with Vernier's. remember to allow for draw as well 229244

   Liked On: 18-07-2023, 09:54 PM

7. 
   Micky Duck liked post by NO4 On thread : No Dice....

   I'd say it was a successful hunt, A new area explored,ya know where to head next time plus any day in the bush is better than being at work

   Liked On: 06-07-2023, 04:36 PM

8. 
   Jhon liked post by NO4 On thread : 303B, Churchill Sporter but what model?

   225718 that little pin,can be made from a bit of wire or small drill bit.

   Liked On: 04-06-2023, 09:26 AM

9. 
   Pengy liked post by NO4 On thread : SHEEEEEIT

   Unfortunately its becoming more common, My wife deals has to deal with this sort of thing 2 or 3 times a year, Its gotten to the point where her and her staff are locked away in a protected (safe)...

   Liked On: 31-05-2023, 08:40 PM

10. 
    Micky Duck liked post by NO4 On thread : SHEEEEEIT

    Unfortunately its becoming more common, My wife deals has to deal with this sort of thing 2 or 3 times a year, Its gotten to the point where her and her staff are locked away in a protected (safe)...

    Liked On: 31-05-2023, 12:04 PM

11. 
    Rusky liked post by NO4 On thread : Near-Miss

    your Very lucky could have ended up deadly, good to hear you ok

    Liked On: 25-05-2023, 12:48 PM

12. 
    57jl liked post by NO4 On thread : Fallow advice

    yea he shot a hind and a yearling( Reds),both off hand snap shoots, very proud dad moment

    Liked On: 24-05-2023, 11:44 PM

13. 
    Morepork liked post by NO4 On thread : Head mounts

    they look awsome,be good if the pill was recovered from the stag and inlayed with the epoxy aswell

    Liked On: 22-04-2023, 04:48 AM

14. 
    dannyb liked post by NO4 On thread : Hello everyone

    no not a golf club or haircut my avatar may give you a clue :thumbs:

    Liked On: 21-04-2023, 08:52 PM

15. 
    Andygr liked post by NO4 On thread : Head mounts

    they look awsome,be good if the pill was recovered from the stag and inlayed with the epoxy aswell

    Liked On: 20-04-2023, 04:47 PM

Page 2 of 11 First 1234567891011 Last

• Jump to page: