Well I can finally close out this thread - I think I'm done. Stock is checkered (I don't think it came out too bad for a first effort), rifle is assembled and sighted in. A few photos for your...
Liked On: 17-01-2023, 09:35 PM
Well I can finally close out this thread - I think I'm done. Stock is checkered (I don't think it came out too bad for a first effort), rifle is assembled and sighted in. A few photos for your...
Liked On: 17-01-2023, 09:15 PM
Well I can finally close out this thread - I think I'm done. Stock is checkered (I don't think it came out too bad for a first effort), rifle is assembled and sighted in. A few photos for your...
Liked On: 17-01-2023, 08:40 PM
Well I can finally close out this thread - I think I'm done. Stock is checkered (I don't think it came out too bad for a first effort), rifle is assembled and sighted in. A few photos for your...
Liked On: 17-01-2023, 08:37 PM
Well I can finally close out this thread - I think I'm done. Stock is checkered (I don't think it came out too bad for a first effort), rifle is assembled and sighted in. A few photos for your...
Liked On: 17-01-2023, 08:29 PM
Well I can finally close out this thread - I think I'm done. Stock is checkered (I don't think it came out too bad for a first effort), rifle is assembled and sighted in. A few photos for your...
Liked On: 17-01-2023, 08:10 PM
Well I can finally close out this thread - I think I'm done. Stock is checkered (I don't think it came out too bad for a first effort), rifle is assembled and sighted in. A few photos for your...
Liked On: 17-01-2023, 08:03 PM
Well I can finally close out this thread - I think I'm done. Stock is checkered (I don't think it came out too bad for a first effort), rifle is assembled and sighted in. A few photos for your...
Liked On: 17-01-2023, 08:03 PM
Here's my contribution, these are RWS Target Rifle with a 60deg conical hollowpoint (made with a dead centre for a lathe). Shot into dense wet newspaper at pointblank. As marked, they are 2.5mm...
Liked On: 04-12-2022, 01:14 AM
Here's my contribution, these are RWS Target Rifle with a 60deg conical hollowpoint (made with a dead centre for a lathe). Shot into dense wet newspaper at pointblank. As marked, they are 2.5mm...
Liked On: 20-11-2022, 06:42 PM
Here's my contribution, these are RWS Target Rifle with a 60deg conical hollowpoint (made with a dead centre for a lathe). Shot into dense wet newspaper at pointblank. As marked, they are 2.5mm...
Liked On: 19-11-2022, 04:49 PM
Here's my contribution, these are RWS Target Rifle with a 60deg conical hollowpoint (made with a dead centre for a lathe). Shot into dense wet newspaper at pointblank. As marked, they are 2.5mm...
Liked On: 19-11-2022, 04:27 PM
Most of it's CCI manufactured, the exception is Winchester ammo (which by reputation is worse). I doubt there's any universally great options given the variation in rifles and batches of even the...
Liked On: 24-09-2022, 08:26 AM
Nelson Collie is still doing bluing, I presume he'd take on the polishing as well.
Liked On: 31-08-2022, 02:28 PM
Looks good. I'd stick with the BLO too. If it was end grain then it might be worth sealing more thoroughly, but otherwise you might as well match the exterior for water resistance. Idle musing...
Liked On: 17-08-2022, 01:47 PM