quentin
Member

611 Likes

Page 18 of 41 First ... 4567891011121314151617181920212223242526272829303132 ... Last

• Jump to page:

1. 
   quentin liked post by dvk-kp On thread : Want to avoid jail - 900m close to a dwelling

   Sounds like your neighbours a cunt. He wouldn’t even hear a suppressed .22 at 900m! Probly wouldn’t hear it at 90m

   Liked On: 20-03-2021, 09:32 AM

2. 
   quentin liked post by Feral On thread : Want to avoid jail - 900m close to a dwelling

   Sounds like your neighbour is a whiney little person who is best cashing in their lifestyle property for a two bedroom flat in town. Sent from my SM-G980F using Tapatalk

   Liked On: 20-03-2021, 09:32 AM

3. 
   quentin liked post by GWH On thread : 2005ish GrandCherokee vs 2007ish Ford Territory

   Yep i'd go with whatever model Landcruiser Prado fits your budget. I run an old '96 Prado 3Lt diesel as my hunting truck, it gets along plenty well enough on the open road when i do longer weekend...

   Liked On: 18-03-2021, 06:00 AM

4. 
   quentin liked post by Gibo On thread : 2005ish GrandCherokee vs 2007ish Ford Territory

   I wouldn't put either in the rough road category myself.

   Liked On: 18-03-2021, 05:59 AM

5. 
   quentin liked post by Lucky On thread : Socks: what do you use

   Thorlos

   Liked On: 13-03-2021, 03:55 PM

6. 
   quentin liked post by hotbarrels On thread : IR Torch recommendation

   What's the scope? Again, no personal experience but I am led to believe that you need to mount the 007 on a scope with no IR lens coatings. I believe the IR coatings will cause issues.

   Liked On: 06-03-2021, 11:47 AM

7. 
   quentin liked post by Skirch On thread : Shotgun Stock CNC Build

   Thought I'd throw up some photos of a buttstock and fore-end I've been making out of some nice chocolatey (is that a word?) walnut I was given. I'd previously done a trial set out of some...

   Liked On: 03-03-2021, 08:17 AM

8. 
   quentin liked post by time out On thread : A fallow meat trip

   An old work Mate from Auckland and I decided a trip down fallow country was overdue - we needed a few fallow for the freezer We met up in Te Awamutu and he dragged my quad and tandem trailer behind...

   Liked On: 03-03-2021, 07:51 AM

9. 
   quentin liked post by Joe_90 On thread : What little pesties did you bowl over today?

   Second time I've shot a ferret feeding on freshly shot rabbit. 161394

   Liked On: 28-02-2021, 09:12 PM

10. 
    quentin liked post by Ftx325 On thread : Stag antler handle ideas

    This one I used the antler tip just to be different. Drilled and slotted antler , drilled a few holes through knife tang and roughed it up with grinder then filled antler slot with epoxy glue and...

    Liked On: 15-02-2021, 08:10 PM

11. 
    quentin liked post by Skirch On thread : First stock bedding Job

    After mixing up the compound that was too runny, I split off half of it to thicken it up without risking ruining the whole lot. In hindsight I should have thickened the whole lot. Mistake three was...

    Liked On: 30-01-2021, 01:22 PM

12. 
    quentin liked post by GWH On thread : HELP WITH MAGPIES

    Ive got an mp3 file of the magpie distress call, play it loud and it works a treat eh Flyblown I can email it to you. I'll be offline until moday night now thou.

    Liked On: 06-01-2021, 12:26 PM

13. 
    quentin liked post by veitnamcam On thread : Advice on outboards

    Fairly well covered above but I will add. 60 two stroke should be enough on that boat if properly loaded and trimmed. 60 hp two stroke and 60hp fourstroke are two completely different things....if...

    Liked On: 30-12-2020, 10:27 PM

14. 
    quentin liked post by 300CALMAN On thread : Wet Tumbling

    Tablespoon of Palmolive and a smidgen of citric acid. Ad water brass and stainless media an stir lots and lots and lots.

    Liked On: 30-12-2020, 08:46 PM

15. 
    quentin liked post by Wingman On thread : San mai style skinning knife build

    The acid etch removed all the loose scale and cleaned out all the rust in the forging pits which was not the look I wanted so I decided to re rust the blade now it was etched so the pits would look...

    Liked On: 29-11-2020, 02:12 PM

Page 18 of 41 First ... 4567891011121314151617181920212223242526272829303132 ... Last

• Jump to page: