shooternz
Member

911 Likes

Page 3 of 61 First 123456789101112131415161753 ... Last

• Jump to page:

1. 
   shooternz liked post by ebf On thread : Case lengthening when bump sizing

   Ok, so here is an experiment for you. Get a shoulder bump / body die that is correctly set up. After firing, size your case, but DO NOT trim it. Keep doing this for several iterations. At some...

   Liked On: 02-03-2023, 02:27 PM

2. 
   shooternz liked post by ebf On thread : Case lengthening when bump sizing

   Add to this that when you start using expander buttons in sizing dies things get even more complex. I don't like expanders at all. For shoulder bumping I either buy body dies, or make them by...

   Liked On: 02-03-2023, 02:26 PM

3. 
   shooternz liked post by Scout On thread : 303 Nitro Proofed

   May not be any load info on the rifle, just nice if it is & a lot of Older English rifles had such, larger cartridges does not mean higher pressure but I'm sure it has ample strength for any .303Brit...

   Liked On: 23-02-2023, 10:59 PM

4. 
   shooternz liked post by gundoc On thread : Dumb question about shooting

   The problem is subject to a steadily increasing error factor that increases exponentially. Bullet stability, velocity, wind, mirage, temperature variation, barrel harmonics, personal ability, etc....

   Liked On: 13-02-2023, 01:04 PM

5. 
   shooternz liked post by 199p On thread : Dumb question about shooting

   TBH Belmont has been some of the most constant ammo ive been able to get my hands on shooting well above its purchase price, Might just be it doesnt like the Sako loads just because its expensive...

   Liked On: 13-02-2023, 01:00 PM

6. 
   shooternz liked post by 7mmsaum On thread : Dumb question about shooting

   Get all the copper/ carbon out of your barrel first Try again

   Liked On: 13-02-2023, 12:55 PM

7. 
   shooternz liked post by Marty Henry On thread : The importance of Seating depths

   That's an impressive 2nd photo cluster of shots but Call me pedantic, in hunting terms does the difference between a 1 moa and .4 moa really matter? It obviously does in target shooting but in the...

   Liked On: 17-01-2023, 10:33 PM

8. 
   shooternz liked post by Basenjiboy On thread : Redundant Calibres

   I must be 'traditional' as I use 7x57 and 222 for hunting. (don't own any of the new calibres). BB

   Liked On: 14-01-2023, 12:52 PM

9. 
   shooternz liked post by Oldbloke On thread : 222 Rem load

   "Originally Posted by caberslash Don't be a cunt." That is utter garbage. 49er was clear he stated he had 1k of bullets he wanted to use and included the powder options. He got replies...

   Liked On: 01-01-2023, 10:56 AM

10. 
    shooternz liked post by JohnDuxbury On thread : 222 Rem load

    2207. 19.5 grains. Any 50 - 55 grain bullet you like.

    Liked On: 01-01-2023, 10:54 AM

11. 
    shooternz liked post by Tommy On thread : 45 Colt and Lee FCD

    Seen lots of brass mangled by shittily machined and finished Lee dies too though

    Liked On: 23-12-2022, 11:47 AM

12. 
    shooternz liked post by Tedz50 On thread : 357 Maximum powders for rifle length barrel.

    I am using 2205 and getting 1800fps with 158 gr XTP,s but according to Mr Google 2200 fps is achievable. If my rifle was in 357 Mag it would still do all I want and cases would be easier to come by....

    Liked On: 19-12-2022, 03:20 PM

13. 
    shooternz liked post by grandpamac On thread : High BC .308 factory rounds

    Greetings All, I don't think that is being a smartarse at all Jhon. NakiNewbie handloading is something that you may wish to consider. If your aim is to produce equivalent cartridges to what you are...

    Liked On: 19-11-2022, 08:15 AM

14. 
    shooternz liked post by SLR On thread : 303 bullets tumbling

    You wont get a good full wood 303 for $800 these days. Lol the days of cheap surplus 303 rifles is well and truly over. As for a stock of new barrels, you're talking about rifles and parts that were...

    Liked On: 17-11-2022, 07:45 PM

15. 
    shooternz liked post by kickinwings On thread : Powder choice for 7-08

    140gr Nosler BT with 2208 or 2206H should do well

    Liked On: 14-11-2022, 09:02 PM

Page 3 of 61 First 123456789101112131415161753 ... Last

• Jump to page: