shooternz
Member

904 Likes

Page 13 of 61 First 123456789101112131415161718192021222324252627 ... Last

• Jump to page:

1. 
   shooternz liked post by grandpamac On thread : Neck turning...is it worth doing ?

   Greetings Ftx325, Not generally thought to be a good idea on factory chambers. Makes a loose neck fit even looser. Only called for if the rifle has a tight neck chamber. These are cut that way by...

   Liked On: 22-12-2020, 08:27 AM

2. 
   shooternz liked post by dannyb On thread : Neck turning...is it worth doing ?

   Do you batch weigh your brass ? Do you anneal ? Do you uniform your flash holes ? Do you trim ? Do you batch weigh your projectiles ? Do you clean and tumble your brass ? Probably a whole heap...

   Liked On: 22-12-2020, 08:27 AM

3. 
   shooternz liked post by ebf On thread : Fireforming case with cleaning patches and pistol powder

   If you want good conformity of the brass to your chamber, you really want to use a projectile and get it jammed into the lands, so that the case base is tight against the bolt face. That way you get...

   Liked On: 19-12-2020, 12:29 AM

4. 
   shooternz liked post by Noswal On thread : Any one seating bullets using a graphite powder?

   Yes when sizing. Lube on the case, dip neck into graphite media with a twist then full size. Even after trimming, neck prep and cleaning there is still graphite in the neck to help with consistent...

   Liked On: 16-12-2020, 02:14 PM

5. 
   shooternz liked post by zimmer On thread : Auto powder dispensers

   I used an RCBS Uniflow thrower for years. Dispensed just under and finished with a trickler on my old Ohaus D5 beam scales. With the Uniflow like any thrower it is all about consistant technique/how...

   Liked On: 16-12-2020, 09:35 AM

6. 
   shooternz liked post by Ryan_Songhurst On thread : Auto powder dispensers

   A decent powder thrower is way quicker than any auto dispenser. Even my "budget" lee thrower will hold a charge from start to finish loading 50 rounds, I weigh every 5th or 6th one quickly to make...

   Liked On: 16-12-2020, 09:29 AM

7. 
   shooternz liked post by GWH On thread : Lightweight loads for 30-06

   I find the IMR4198 works far better than 2206H for reduced charge/recoil loads, it gives far better accuracy and can be used for almost any cartridge from 223 to 3006.

   Liked On: 07-12-2020, 10:22 AM

8. 
   shooternz liked post by Tahr On thread : 223 ELDM powder choice

   I use 2206 with 77 grn Tipped MK and gimp uses 2208 with 80 ELDM. I can't talk for gimp but I'm sure his is super accurate as is mine. I would load a few with each powder to try. Just go for the...

   Liked On: 07-12-2020, 10:10 AM

9. 
   shooternz liked post by R93 On thread : Load issues (blowback) 454 Casull

   Max load getting blowback? Sounds a bit odd. I would just change powder and see how that goes. Sent from my SM-T510 using Tapatalk

   Liked On: 07-12-2020, 09:52 AM

10. 
    shooternz liked post by bunji On thread : Lightweight loads for 30-06

    One of the rifles l have never been able to bring myself to sell is a nearly 20 yr old Rem Mountain rifle in 06 my wife brought me. I have taken it around the world as my back up rifle as a guide,...

    Liked On: 04-12-2020, 01:25 PM

11. 
    shooternz liked post by Moa Hunter On thread : Fireforming New Brass

    Which case is the longer ? With Ackley cases they are designed slightly shorter than the parent, meaning that 2506 factory loads can be fired in a 2506 Ackley chamber as an example and headspace...

    Liked On: 04-12-2020, 01:22 PM

12. 
    shooternz liked post by veitnamcam On thread : 223 loads for wind

    53 gr vmax is probably the best bc bullet you will shoot out of a 12 twist. Drift being both a fuction of bc and speed run some numbers and see what you get.

    Liked On: 29-11-2020, 02:02 PM

13. 
    shooternz liked post by caberslash On thread : Tactical High Powered Scope Confusion

    154701

    Liked On: 28-11-2020, 04:07 PM

14. 
    shooternz liked post by Moa Hunter On thread : Meat hunter in NZ

    He Recovers ALL of the meat and said he had the rest of the day packing it out with the one stag. That second stag was in his prime and carried a top notch head so better to leave him as a breeder...

    Liked On: 28-11-2020, 03:32 PM

15. 
    shooternz liked post by Shadowsol On thread : Meat hunter in NZ

    I haven't watched the NZ episodes (will do now though) - but I have watched the last 3 seasons - I can see some of the reasons they may not like the NZ hunting scene, some of them I agree with. ...

    Liked On: 28-11-2020, 03:28 PM

Page 13 of 61 First 123456789101112131415161718192021222324252627 ... Last

• Jump to page: