shooternz
Member

979 Likes

Page 13 of 66 First 12345678910111213141516171819202122232425262763 ... Last

• Jump to page:

1. 
   Bill999 liked post by shooternz On thread : 7x57 subsonic

   You will have a stability problem with the 175 grain at subsonic velocity the 160 grain 7mm I sell is very marginal at 1000fps it is starting to tip at 50 metres the 175 are quite a bit longer, I...

   Liked On: 06-04-2022, 03:54 PM

2. 
   Marty Henry liked post by shooternz On thread : 7x57 subsonic

   You will have a stability problem with the 175 grain at subsonic velocity the 160 grain 7mm I sell is very marginal at 1000fps it is starting to tip at 50 metres the 175 are quite a bit longer, I...

   Liked On: 06-04-2022, 03:09 PM

3. 
   Moa Hunter liked post by shooternz On thread : 7x57 subsonic

   You will have a stability problem with the 175 grain at subsonic velocity the 160 grain 7mm I sell is very marginal at 1000fps it is starting to tip at 50 metres the 175 are quite a bit longer, I...

   Liked On: 06-04-2022, 03:01 PM

4. 
   Micky Duck liked post by shooternz On thread : 7x57 subsonic

   You will have a stability problem with the 175 grain at subsonic velocity the 160 grain 7mm I sell is very marginal at 1000fps it is starting to tip at 50 metres the 175 are quite a bit longer, I...

   Liked On: 06-04-2022, 01:03 PM

5. 
   MB liked post by shooternz On thread : Recommend a 300BLK factory subsonic round

   The problem with factory Blackout loads is they are optimised for the AR15 platform the gas system bleeds off gas to operate the action bolt actions use all the gas for velocity unless you reload...

   Liked On: 31-03-2022, 10:10 PM

6. 
   Moa Hunter liked post by shooternz On thread : Recommend a 300BLK factory subsonic round

   The problem with factory Blackout loads is they are optimised for the AR15 platform the gas system bleeds off gas to operate the action bolt actions use all the gas for velocity unless you reload...

   Liked On: 31-03-2022, 10:12 AM

7. 
   m101a1 liked post by shooternz On thread : Recommend a 300BLK factory subsonic round

   The problem with factory Blackout loads is they are optimised for the AR15 platform the gas system bleeds off gas to operate the action bolt actions use all the gas for velocity unless you reload...

   Liked On: 30-03-2022, 10:48 PM

8. 
   Micky Duck liked post by shooternz On thread : best 308 projectile for shooting sika at close range

   You could try Hornady SST's or If like you say only out to 100 metres a 150 Round nose any bullet for the 30/30 the 170 grain are a great deer bullet very popular in the USA,

   Liked On: 26-03-2022, 06:22 PM

9. 
   veitnamcam liked post by shooternz On thread : best 308 projectile for shooting sika at close range

   You could try Hornady SST's or If like you say only out to 100 metres a 150 Round nose any bullet for the 30/30 the 170 grain are a great deer bullet very popular in the USA,

   Liked On: 22-03-2022, 07:12 PM

10. 
    40mm liked post by shooternz On thread : 54 cal sharps

    When I had my one I got fed up with make the paper cartridges, and just dropped a bullet in the barrel and filled it with powder worked better than the cartridges with more consistent ignition.

    Liked On: 18-03-2022, 02:33 PM

11. 
    T.FOYE liked post by shooternz On thread : Committed the newby mistake of seating too far...

    It happens to everyone with cast bullets at some time specially with a new gun, Cast bullets don't like being jammed into the rifling just a light touch; better to seat to the crimp groove if it has...

    Liked On: 16-02-2022, 10:39 PM

12. 
    winaa liked post by shooternz On thread : 338 Federal versus 358 Winchester

    How about this one 82231 No gas check but ideal for subs

    Liked On: 16-02-2022, 03:54 PM

13. 
    veitnamcam liked post by shooternz On thread : Committed the newby mistake of seating too far...

    It happens to everyone with cast bullets at some time specially with a new gun, Cast bullets don't like being jammed into the rifling just a light touch; better to seat to the crimp groove if it has...

    Liked On: 15-02-2022, 10:45 PM

14. 
    Micky Duck liked post by shooternz On thread : Committed the newby mistake of seating too far...

    It happens to everyone with cast bullets at some time specially with a new gun, Cast bullets don't like being jammed into the rifling just a light touch; better to seat to the crimp groove if it has...

    Liked On: 15-02-2022, 09:16 PM

15. 
    winaa liked post by shooternz On thread : .277 bullet mold

    Not a good idea the 270 is not really suitable for cast bullet there are few mold s available, the case capacity is way too large the barrel twist is too fast velocity is limited to 1500-1800fps, No...

    Liked On: 15-02-2022, 02:07 PM

Page 13 of 66 First 12345678910111213141516171819202122232425262763 ... Last

• Jump to page: