T.FOYE
Member

304 Likes

Page 1 of 21 123456789101112131415 ... Last

• Jump to page:

1. 
   T.FOYE liked post by TeRei On thread : Annealing

   https://www.ampannealing.com/articles/56/annealing-under-the-microscope/

   Liked On: 19-04-2024, 02:40 PM

2. 
   T.FOYE liked post by john m On thread : What Have You Loaded Today

   Loaded a few with 400gr fp over 75gr AR2206H. 248200

   Liked On: 17-04-2024, 06:58 AM

3. 
   T.FOYE liked post by Pommy On thread : What Have You Loaded Today

   Formed a few more 8.6 Blackout cases ready to go. 247933 Neck turning an absolute necessity because of how thick the necks come out. Time consuming. But pretty.

   Liked On: 17-04-2024, 06:58 AM

4. 
   T.FOYE liked post by gimp On thread : Incline / decline shooting

   I wouldn't overthink it for closer ranges - 275m with my data is 1.3MIL for flat and 1.0 for -30 degrees. That is 34 vs 26cm. Most people are very poor at judging slope - if you are not...

   Liked On: 04-04-2024, 11:44 AM

5. 
   T.FOYE liked post by BMcB On thread : What Have You Loaded Today

   6mm Creedmoor. 108g Berger BTT over Staball 6.5 5 shots into16mm at 186m That'll do 246821

   Liked On: 30-03-2024, 11:03 PM

6. 
   T.FOYE liked post by svt40 On thread : What Have You Loaded Today

   [ATTACH]245775[/ATTACH/] Had a go at loading some 1895 Nagant rounds. a mashup of M1 carbine, 32S&WL and 7.62 tokarev dies and we have potentially viable results

   Liked On: 30-03-2024, 10:59 PM

7. 
   T.FOYE liked post by Oldbloke On thread : What could cause this?

   Could it be parallex related?

   Liked On: 28-03-2024, 06:14 AM

8. 
   T.FOYE liked post by grandpamac On thread : What could cause this?

   Greetings, I suggest you repeat the test with a better aiming mark. A hollow square or circle that you can quarter with your cross hairs will work a lot better. Also consider zeroing at 200 metres....

   Liked On: 28-03-2024, 06:13 AM

9. 
   T.FOYE liked post by Trout On thread : What could cause this?

   Doesnt take much breeze to move them at 300yds left or right.I use a bit of light ribben hanging off a electric fence stay.I dont pull the trigger till ribben drops,hangs plum then squezze off the...

   Liked On: 28-03-2024, 06:12 AM

10. 
    T.FOYE liked post by akaroa1 On thread : What Have You Loaded Today

    The basic Lee 450 Grain .515 mould Sized .510 before and after powder coat The .515 is for old worn bore 12.7s and 50-70s But is best sized .510 if the bore is good. All five of my vintage 50...

    Liked On: 26-03-2024, 10:26 PM

11. 
    T.FOYE liked post by DBD On thread : What's up with this ?

    Just read through this, what a nob!

    Liked On: 25-03-2024, 07:38 AM

12. 
    T.FOYE liked post by Oldbloke On thread : What's up with this ?

    Nothing to joke about. Do the obvious, Check scope mounts and screws. Check stock screws. Stock screws touching barrel? Swap scope. Different ammo

    Liked On: 25-03-2024, 07:22 AM

13. 
    T.FOYE liked post by akaroa1 On thread : What Have You Loaded Today

    I loaded some 500 3" BPE I'm already on plan C for this roar and the way things are going anything could happen. So roll up some of these and then have options for plan D, E and F 246640 ...

    Liked On: 25-03-2024, 06:50 AM

14. 
    T.FOYE liked post by Marty Henry On thread : BAD FLYER 9"

    A tip coming loose on loading and lying to one side on firing wedging against the projectile could account for it. I've had tips shatter on the breech face when single loading and the round hasn't...

    Liked On: 25-03-2024, 06:43 AM

15. 
    T.FOYE liked post by Kimber 7mm-08 On thread : BAD FLYER 9"

    Baffle strike or loose suppressor?

    Liked On: 25-03-2024, 06:40 AM

Page 1 of 21 123456789101112131415 ... Last

• Jump to page: