Tech
Member

175 Likes

Page 3 of 12 First 123456789101112 Last

• Jump to page:

1. 
   JohnQT liked post by Tech On thread : Speer 55gr Spitzer

   JohnQT if you are referring to the Speer part No 1047 55 grain spritzer then I have used them in a 223 for goats. Also I have used them in a 22-250 and a 220 Swift for goats, deer and pigs. It was...

   Liked On: 11-12-2022, 09:28 PM

2. 
   Moa Hunter liked post by Tech On thread : 7mm Gamechanger in 270

   Four or five years ago a Rotorua gun store owner showed me a box of Hornady factory 308 ammo that had one round of 243 ammo in it.

   Liked On: 10-10-2022, 06:59 AM

3. 
   dannyb liked post by Tech On thread : 7mm Gamechanger in 270

   There is mention of this amongst this thread. 207730

   Liked On: 09-10-2022, 09:05 PM

4. 
   tetawa liked post by Tech On thread : 7mm Gamechanger in 270

   There is mention of this amongst this thread. 207730

   Liked On: 09-10-2022, 09:02 PM

5. 
   caberslash liked post by Tech On thread : No more powder

   grandpamac if you go onto the Hodgdon site and click on any of the Enduron powders and scroll to the bottom of the "Product Overview" you will see "This product was discontinued in 2022".

   Liked On: 04-09-2022, 07:49 PM

6. 
   Moa Hunter liked post by Tech On thread : Interesting rimfire models: your reviews, pics, comments

   From memory the Mauser 201 and Voere 2000 were both chambered in 22 WMR as well as 22 LR which may explain the longer bolt throw length.

   Liked On: 25-08-2022, 03:29 PM

7. 
   Mathias liked post by Tech On thread : Drying Cases

   When I asked AMP about drying brass Alex sent an email saying pre-heat the oven at 120°C and put the cases in for 10-15 minutes. That worked fine and I had no discolouration. My wife bought an air...

   Liked On: 19-06-2022, 05:08 PM

8. 
   7mm Rem Mag liked post by Tech On thread : 223 bushing for redding compitition die

   Out of curiosity I pulled my various 223 ammo out of the safe and these are the measurements of the loaded ammo, ADI Factory Load .247" Norma Factory Load .247" Norma Reload .247" Lapua Reload...

   Liked On: 24-04-2022, 03:43 PM

9. 
   Waynesworld liked post by Tech On thread : Weihrauch HW66 & HW 60J

   CR Pain also distributes Weihrauch rifles. Along with the different stock design between the HW 66 and HW 60J there is also a weight difference. The HW 66 weigh 3.15 kg compared to 3.6 kg for the...

   Liked On: 24-03-2022, 08:24 PM

10. 
    GuyDowding liked post by Tech On thread : Case Neck runout with redding type s bushing die

    If there is more than 5 thou difference between your fired case neck outside diameter and the sized case then Redding suggest you use more than one bushing. I had this same issue when sizing for...

    Liked On: 07-03-2022, 08:20 PM

11. 
    Trav-6mmrem liked post by Tech On thread : Ruger M77 International

    Back in the mid 80s I sold a new International in 250 Savage. It was one of the rifles Howard Lopdell imported when I had a small gun shop in Rotorua. It had a very nice stock for a Ruger.

    Liked On: 07-03-2022, 08:19 PM

12. 
    Jamesyd liked post by Tech On thread : Ruger M77 International

    Back in the mid 80s I sold a new International in 250 Savage. It was one of the rifles Howard Lopdell imported when I had a small gun shop in Rotorua. It had a very nice stock for a Ruger.

    Liked On: 07-03-2022, 08:15 PM

13. 
    Mick Hunter liked post by Tech On thread : Case Neck runout with redding type s bushing die

    If there is more than 5 thou difference between your fired case neck outside diameter and the sized case then Redding suggest you use more than one bushing. I had this same issue when sizing for...

    Liked On: 07-03-2022, 05:38 AM

14. 
    Micky Duck liked post by Tech On thread : 22 Magnum 1885 barrel re line and modern ammunition

    @akoroa1 the Ruger American Compact in 22 WMR have a 1:14" twist from what I have read.

    Liked On: 06-03-2022, 04:19 PM

15. 
    Tikka7mm08 liked post by Tech On thread : Gunsmith Howard C Lopdell

    Between the mid to late 80's Howard had a company called South Pacific Gun Supplies based in Beachlands. He imported rifles from the USA and sent several of them down to me in Rotorua where I had a...

    Liked On: 03-03-2022, 10:24 AM

Page 3 of 12 First 123456789101112 Last

• Jump to page: