Tommy
Member

4964 Likes

Page 77 of 331 First ... 276364656667686970717273747576777879808182838485868788899091127177 ... Last

• Jump to page:

1. 
   Tommy liked post by mucko On thread : AIMNZ ENGINEERING

   100647100648 can do this pre made $80 including postage. 10m hose.

   Liked On: 12-12-2018, 06:48 PM

2. 
   Tommy liked post by R93 On thread : AIMNZ ENGINEERING

   You can't be talking about me? I only liked blue crayons. (Blue was training not red, ya mong) Red ones were too spicey[emoji16] Sent from my SM-G965F using Tapatalk

   Liked On: 12-12-2018, 06:47 PM

3. 
   Tommy liked post by mucko On thread : AIMNZ ENGINEERING

   Hi guys just looking to promote my business a bit. the base of the business is maintenance engineering, i also make bipod spikes out of aliminium for $55 + postage and stock round gongs 7" and 9"...

   Liked On: 11-12-2018, 06:53 PM

4. 
   Tommy liked post by Maca49 On thread : Gun Porn, show off your new toys

   My selection at the Xmas shoot today!100468 100469

   Liked On: 09-12-2018, 09:31 PM

5. 
   Tommy liked post by NZShoota On thread : Gun Porn, show off your new toys

   Just for you Ryan :thumbsup: 100466 100467

   Liked On: 09-12-2018, 09:30 PM

6. 
   Tommy liked post by Carlsen Highway On thread : Here We Go Again

   And now its Global warming. So if you argue against it, you're against global warming. Except when its not warming - then its called climate change.

   Liked On: 08-12-2018, 12:40 PM

7. 
   Tommy liked post by Kamel On thread : Lizards

   Thought I would give you folks a few photos of lizards we see out here quite often. First is two stumpy tailed shingle backs, commonly called Bogeyes, having a bit of a tussle showing off to a...

   Liked On: 08-12-2018, 08:40 AM

8. 
   Tommy liked post by Kurt On thread : Gun Porn, show off your new toys

   100235

   Liked On: 06-12-2018, 06:01 PM

9. 
   Tommy liked post by csmiffy On thread : reloading press

   Tommy that was my impression of her also. as an aside I have asked my friend what his press was and it is a large O frame Hornady. It handles the 416 rem as that's what I reloaded mine with so all...

   Liked On: 05-12-2018, 08:38 PM

10. 
    Tommy liked post by Marty Henry On thread : Dundee Yards

    When we walked the milford track back in 83 I think it was we met an old retired farmer from pio pio half way through the first day. He was coming back from Milford having gone both ways. Footwear...

    Liked On: 03-12-2018, 06:06 PM

11. 
    Tommy liked post by BRADS On thread : Dundee Yards

    I have my doubts about that rangefinder Dundee. Ive also looked through the scope of that 22 and couldn't see my ute at 20 yards . But I'll give the drunk one thing he can shoot, he sacked a...

    Liked On: 03-12-2018, 06:06 PM

12. 
    Tommy liked post by ebf On thread : Dundee Yards

    I was waiting for the classic fishing photo where you hold the fishy out at full arms length to make it look larger... Mind you, if Dundee held up a bunny it would probably look like a bloody...

    Liked On: 03-12-2018, 06:05 PM

13. 
    Tommy liked post by Dundee On thread : Dundee Yards

    Righto you un believers. For the new members I'm 5'4 ad weigh fuck all.Served in the NZDF at a young age and have been shooting ever since. My trusty .22lr rifle has been getting shit from the...

    Liked On: 03-12-2018, 06:03 PM

14. 
    Tommy liked post by tanqueray On thread : slugging a bore

    I use wooden dowel and a rubber mallet so no chance of damaging the bore. The wooden dowel is cut into 200m sections so that it doesn’t warp too much, just add the next section when you’re getting...

    Liked On: 03-12-2018, 06:00 PM

15. 
    Tommy liked post by Marty Henry On thread : slugging a bore

    Oil the bore and grease the slug the rod that taps the slug through should be near bore diameter and brass or similar. A series of progressivly longer rods is best to prevent flexing.

    Liked On: 03-12-2018, 06:00 PM

Page 77 of 331 First ... 276364656667686970717273747576777879808182838485868788899091127177 ... Last

• Jump to page: