Try putting a half inch socket over the case. Change the Phillips head screw for a bolt with some fat washers between the bolt head and the socket and tighten with a spanner. Clearly there was not...
Liked On: 01-03-2021, 04:25 PM
It's too easy to blame runout for the so-so accuracy. As has been said, the projectile/load/powder just may not be the right one. As for reducing runout, the simplest way is probably to use a std...
Liked On: 01-03-2021, 09:40 AM
Welcome. Hunted throughout that area when I was a kid and back doing a bit there again now.... :) I loaned this book out about 25-years ago and it was never returned until about 3-months ago. It's...
Liked On: 28-02-2021, 05:58 PM
Its a .270 - has been for a while. Often referred to. I expect it is to do with being able to display Federal factory ammo on the series. Shorter barrel .270 is a good choice though. 270 or...
Liked On: 26-02-2021, 05:38 PM
If your last 14 deer were all inside 150y why even bother with cds? You could go old school and zero at 200 and shoot anything out to 250
Liked On: 26-02-2021, 12:35 PM
The spiny green ones here are smart. They know they are spiny, and so live on the Rimu. Their cousins - the smooth greens - live on the Rata. For anyone interested, the eggs can be collected and...
Liked On: 26-02-2021, 10:33 AM
This incredible “bramble” appeared on a Red Band gumboot this morning. I thought it was stuck on the boot and damn nearly grabbed it to pull it off. Check out the astonishing replication of a bramble...
Liked On: 25-02-2021, 07:28 PM
This may well belong to someone on here? Absolutely immaculate machining and woodwork. 1/4 scale American civil war Whitworth cannon if memory serves me right. Half a Bofors barrel. Came to my...
Liked On: 21-02-2021, 12:30 PM
Well, I brought 4 packets of .22 ammo to try out: Aus Winchester subsonic 22 LR, Eley subsonic 22LR, Remington Green subsonic, and a pkt of CCI rapid-fire pistol shorts. I had to buy them at the...
Liked On: 18-02-2021, 07:06 PM
Sorry about the delay, and yes the write-up was a bit long and probably would have been better served with a contents listing: 1. Source quality brass in 8x57 2. Neck down to .308 ( .308Win...
Liked On: 16-02-2021, 07:37 PM
I have been using Hornady 6.5 Creedmoor brass for 2 years. Some of then are on their 7’th reload and I can feel some primer pockets becoming more worn than others, but not to the point where I feel I...
Liked On: 16-02-2021, 07:23 PM
Forster and Lee are the best FL dies I have used with the stock expander. I too polish them to a mirror finish. The worst I have used are Hornady (243, 7mm08, 308), and a newish Redding FL die in...
Liked On: 16-02-2021, 02:44 PM
For the doubters here's the pic of the target with nothing in the way. 160526
Liked On: 15-02-2021, 08:06 PM
Here ya go 160504 160505 Same era I remember getting on the Arthurs Pass railcar at Christchurch Railway station with my pack and a 303. It was ski season and it was packed. No-one even blinked...
Liked On: 15-02-2021, 07:39 PM
Greeting Micky and All, The die makers are between a rock and a hard place when it comes to die dimensions. There is considerable variation in chambers and case wall and neck thickness. Dies need to...
Liked On: 15-02-2021, 05:11 PM