Bagheera
Member

1157 Likes

Page 50 of 78 First ... 3637383940414243444546474849505152535455565758596061626364 ... Last

• Jump to page:

1. 
   Bagheera liked post by Bill999 On thread : Leupold VX-3i 4.5-14x40 CDS-ZL Duplex

   The vx3 won't be ffp They are nice and light but limited in the eyebox for eye relief, the vx-5 vx-6 vxr bigger eye box is really forgiving in comparison The vx5 mentioned is a big step in...

   Liked On: 16-10-2020, 01:10 PM

2. 
   Bagheera liked post by zimmer On thread : Mil-Dot reticle help pls clever fellas

   Just to confuse.. Definitions of the angular mil There are 2000π milliradians (≈ 6283.185 mrad) in a circle; thus a milliradian is just under 1⁄6283 of a circle, or ≈ 3.438 minutes of arc....

   Liked On: 13-10-2020, 06:18 PM

3. 
   Bagheera liked post by ebf On thread : Barrels ruined by cleaning

   It's not cleaning that ruins barrels... it is cleaning in stupid ways. Fullbore target shooters and benchrest guys must be the most OCD rifle cleaners I have ever encountered, and I don't see...

   Liked On: 12-10-2020, 12:25 PM

4. 
   Bagheera liked post by stagstalker On thread : Insight / Discussion RE magnum calibres for mountain rifle

   When you start getting out around 4-500 and beyond its impact speeds, retained energy and wind drift that start becoming important. That's where the more efficient cartridges assist the shooter. Most...

   Liked On: 04-10-2020, 08:54 PM

5. 
   Bagheera liked post by Pav On thread : Sako Vixen L461 .222 first shoot

   Finished work early today so made the most of the good weather and headed to Tokoroa for my first shoot of the wee Vixen. After bore sighting, got it on paper at 50m using Belmont loaded Hornady 50g...

   Liked On: 04-10-2020, 08:47 PM

6. 
   Bagheera liked post by Woody On thread : New scope

   Unless you have a very large objective lens, say like 50 - 56mm then your alway goung to get smaller field of view when you go higher magnification. Of course 2x mag will have more fov (and more...

   Liked On: 26-09-2020, 11:25 PM

7. 
   Bagheera liked post by vulcannz On thread : Thinking between 3 rifles

   mimms is correct though.

   Liked On: 03-09-2020, 11:45 PM

8. 
   Bagheera liked post by Nick-D On thread : Long Distance Shooting Course? Bay of Plenty

   Fuck yessss. Bring it on

   Liked On: 30-08-2020, 08:45 PM

9. 
   Bagheera liked post by ebf On thread : Long Distance Shooting Course? Bay of Plenty

   I'm going to go out on a limb here and suggest that the chances of you having any lasting benefit from a "course" will be minimal. Long range shooting is about practice, practice, practice. ...

   Liked On: 30-08-2020, 08:44 PM

10. 
    Bagheera liked post by Puffin On thread : 440m ladder test

    My observation has been that most people who come on here asking about ladder tests already know the method they are intent on using, and will go on to interpret the data in the way to which they are...

    Liked On: 04-08-2020, 11:37 PM

11. 
    Bagheera liked post by matagouri On thread : First Helicopter Company pulls The Pin On The Tahr Cull

    I wonder if there pulling out was due to additional overseas pressure put on Alpine by hunting groups such as sci etc....?????? Boar freak, go for it mate. Can assure you during early 80,s you...

    Liked On: 22-07-2020, 01:24 PM

12. 
    Bagheera liked post by veitnamcam On thread : Is this normal for my brass

    Almost correct, what causes case head separation in that area is not actually anything to do with the die working the brass in that area....the die actually sizes very little near the case head....

    Liked On: 13-07-2020, 10:42 AM

13. 
    Bagheera liked post by Bos On thread : Must have Classic hunting books.

    The Sharp Shooter, by Matt and Bruce Grant

    Liked On: 07-07-2020, 11:34 PM

14. 
    Bagheera liked post by Shamus_ On thread : Must have Classic hunting books.

    Hunter Climb High by Keith Severinsen and Deer Hunter by Joff Thomson are both good reads

    Liked On: 07-07-2020, 11:34 PM

15. 
    Bagheera liked post by Wingman On thread : Hi-Tec Howa Mini Carbon stocks ready...

    I currently have one modeled in Solidworks.. for a lightweight chassis project, 171.5mm is the exact measurement of holes center to center.

    Liked On: 07-07-2020, 11:37 AM

Page 50 of 78 First ... 3637383940414243444546474849505152535455565758596061626364 ... Last

• Jump to page: