caberslash
Member

2734 Likes

Page 74 of 183 First ... 246061626364656667686970717273747576777879808182838485868788124174 ... Last

• Jump to page:

1. 
   caberslash liked post by 7mmsaum On thread : 223 on deer

   60g Nosler Ballistic Tips @ 3100 fps 195569 Surgically precise :) 195570

   Liked On: 26-04-2022, 03:51 AM

2. 
   caberslash liked post by gimp On thread : 223 on deer

   CCI 450. Small rifle magnum. Cos I have a lot of them.

   Liked On: 26-04-2022, 03:51 AM

3. 
   caberslash liked post by 7mm Rem Mag On thread : 223 on deer

   All I could pick up was cci 450. At least I think thats what I orded. Any good?

   Liked On: 26-04-2022, 03:51 AM

4. 
   caberslash liked post by 00buck On thread : Brand new Hatsan shotgun exploded in my face

   Similar thing happened to a friend about 12 years ago with a brand new Escort 3.5" magnum. We tried out his new gun a few weeks before opening, only fired a few rounds before turning into a single...

   Liked On: 25-04-2022, 04:38 PM

5. 
   caberslash liked post by gundoc On thread : Brand new Hatsan shotgun exploded in my face

   The gun needs to be examined and a report produced before it gets into the hands of the dealer/importer. There are potential mechanical failures that could have caused this. I have done several such...

   Liked On: 25-04-2022, 04:35 PM

6. 
   caberslash liked post by Beavis On thread : Brand new Hatsan shotgun exploded in my face

   Not the first time I've seen a Hatsan/Escort shotgun trashed by and out of battery

   Liked On: 25-04-2022, 04:34 PM

7. 
   caberslash liked post by Tertle On thread : Lee Enfield Price check

   Thanks, i looked on the yellow site last night and that was painful! 195511 195512 195513 195514 195515 195516

   Liked On: 25-04-2022, 04:32 PM

8. 
   caberslash liked post by Jaco Goosen On thread : new barrel - hard to eject rounds

   alphaDelta, answering a question you asked earlier. What can you expect after having a barrel replaced. The short answer: you can expect whatever you specified/negotiated before the build started....

   Liked On: 25-04-2022, 04:27 PM

9. 
   caberslash liked post by GWH On thread : new barrel - hard to eject rounds

   So it seems the smith never test fired it then

   Liked On: 24-04-2022, 11:04 AM

10. 
    caberslash liked post by gundoc On thread : new barrel - hard to eject rounds

    The usual cause of such problems is a rough chamber, normally caused by trying to take too large cuts. The reamer must be withdrawn , cleaned and lubed, many times, especially when getting near the...

    Liked On: 24-04-2022, 11:04 AM

11. 
    caberslash liked post by dannyb On thread : Hi Tech Composites stocks on Howa 1500

    The Howa Alpine is mint, however I found it to be very short L.O.P hopefully the hitech ones are a little bit longer.

    Liked On: 24-04-2022, 06:09 AM

12. 
    caberslash liked post by GWH On thread : new barrel - hard to eject rounds

    Ive struck a very similar issue where fired brass was very hard to extract from chamber, bolt had to be taped rearward to pull out brass from chamber. The issue was the new barrel had been...

    Liked On: 24-04-2022, 04:29 AM

13. 
    caberslash liked post by GWH On thread : Hi Tech Composites stocks on Howa 1500

    Yep not many fancy (expensive) CF stocks are that light. I have two that weight just less than that. Both Mod 7 stocks, one is a Stug and the other is a Wildcat Composites out of Canada. Kens new...

    Liked On: 24-04-2022, 01:24 AM

14. 
    caberslash liked post by mikee On thread : new barrel - hard to eject rounds

    Best to let the builder have a look at it and remedy it first. If its a std rem factory action which has been rebarreled then it should be quite a simple fix you would hope.

    Liked On: 23-04-2022, 10:40 PM

15. 
    caberslash liked post by alphaDelta On thread : new barrel - hard to eject rounds

    Thanks for taking the time mate, awesome info cheers

    Liked On: 23-04-2022, 10:40 PM

Page 74 of 183 First ... 246061626364656667686970717273747576777879808182838485868788124174 ... Last

• Jump to page: