Calvnz1
Member

73 Likes

Page 3 of 5 First 12345 Last

• Jump to page:

1. 
   Calvnz1 liked post by 7mmsaum On thread : Help

   Seating die screwed down into the press too far

   Liked On: 05-08-2023, 07:45 PM

2. 
   Calvnz1 liked post by Husky1600#2 On thread : Factory ammo overcharge ?

   And put a tight cleaning rod slowly through the barrel. I suspect the third shot wasnt the problem, it was a squib load on the second. And your third shot suffered the consequences. A tight cleaning...

   Liked On: 29-07-2023, 10:11 AM

3. 
   Calvnz1 liked post by No.3 On thread : Factory ammo overcharge ?

   That and weigh the empty cases, one might be thicker somewhere giving less capacity? Can't have been a major overcharge as the brass or rifle didn't let go, but do not shoot it until its been...

   Liked On: 29-07-2023, 09:59 AM

4. 
   Calvnz1 liked post by veitnamcam On thread : Factory ammo overcharge ?

   Not 303 but I have had fed blue box stamp and shave brass and stiff bolt lift in 308..... generally its good but one box I had 50/50 over pressure.

   Liked On: 28-07-2023, 10:51 PM

5. 
   Calvnz1 liked post by blair993 On thread : Thoughts on discovery scopes.

   i have a athlon 5-25 on my t1x 22lr. and just putting a pst2 5-25 on my 10/22.

   Liked On: 26-07-2023, 09:48 PM

6. 
   Calvnz1 liked post by Tentman On thread : Dayattherange Flyswatter Challenge

   Target shot Sunday arvo with 1934 Winchester Model 52 (a so called "pre A": 229627 And a better one with the CZ 457 "pencil barrel" 229628 I dont think there's any embarrassment until...

   Liked On: 26-07-2023, 12:29 AM

7. 
   Calvnz1 liked post by Hermitage On thread : Dayattherange Flyswatter Challenge

   That 'fly swatter' challenge is more difficult than it looks. The fly is narrow, so each heartbeat moved the reticle a little to the right and left of the fly. I thought about swiping some beta...

   Liked On: 26-07-2023, 12:28 AM

8. 
   Calvnz1 liked post by Micky Duck On thread : Dayattherange Flyswatter Challenge

   Im ever so tempted to accept the challenge..and then use 2 rounds of #8 birdshot out of .12ga with my tightest choke LOL

   Liked On: 26-07-2023, 12:27 AM

9. 
   Calvnz1 liked post by Tentman On thread : Dayattherange Flyswatter Challenge

   Hey old Mr Revolver Guy (Elijah) has posted up a neat new challenge at https://dayattherange.com/?p=11278 Target is here. https://dayattherange.com/wp-content/uploads/2023/07/img110.pdf Make sure...

   Liked On: 24-07-2023, 08:15 PM

10. 
    Calvnz1 liked post by 300CALMAN On thread : New Here got my licence this month Goat Problem

    7.62 x 39 is also a good cal for goats and deer at close range. Good luck!

    Liked On: 16-07-2023, 04:00 PM

11. 
    Calvnz1 liked post by Grey Kiwi On thread : Accura scopes

    I wrote and asked them where the scopes are made (they are an Aussie company). Made in China, but there are good and bad products coming from China. Those scopes may be fine. I was looking at the...

    Liked On: 26-06-2023, 09:13 PM

12. 
    Calvnz1 liked post by TLB On thread : .303s

    I have received these .303s as part of an estate. I have a couple of my own sporterised ones but know very little about them. Anyone have much knowledge on the three below? Fairly common models?...

    Liked On: 25-06-2023, 10:11 PM

13. 
    Calvnz1 liked post by 6.5 CRD On thread : Something a few may appreciate.. they dont make em like they used to

    Stoked to have my fathers 7x57 back in my hands after a number of years, big thanks to Kiwi Greg for sorting out the tight bolt + arranging getting it up to auckland for me. Husqvarna Vapenfabriks...

    Liked On: 22-06-2023, 09:29 PM

14. 
    Calvnz1 liked post by BMF On thread : New guy

    Hello everyone... new to site... have heard good things..

    Liked On: 17-06-2023, 05:59 PM

15. 
    Calvnz1 liked post by Makwa On thread : Greetings from British Columbia

    Since I have been reading some former posts on your site and, since I think NZ is a beautiful place I hope to visit some day, I decided to join. :) I am retired now after many years of ranching and...

    Liked On: 11-06-2023, 07:57 PM

Page 3 of 5 First 12345 Last

• Jump to page: