About chainsaw

Basic Information


About chainsaw
Location:
Norf

Statistics


Total Posts
Total Posts
5,469
Posts Per Day
1.52
General Information
Last Activity
Yesterday 10:46 PM
Join Date
08-07-2014
Referrals
0

1 Friend

Showing Friends 1 to 1 of 1

2723 Likes

  1. Moa Hunter
    Moa Hunter liked post by chainsaw On thread : Empty brass on plane
    I have flown to/from Sth Is a bit (usually Q’town) with firearms & ammo. All following the procedures outlined by Air NZ. Always in checked luggage. Have had them (Av Sec) confiscate fired brass (20...
    Liked On: 01-10-2023, 09:25 AM
  2. Micky Duck
    Micky Duck liked post by chainsaw On thread : Rifle Scope
    A 3-9x42 or similar would be a good option for your hunting, plenty of older quality scopes around that you pick up for $300 -$600 or you could spend a bit more for a 2-10x or 3-12x or 3-15x. If you...
    Liked On: 27-09-2023, 03:35 PM
  3. BK10
    BK10 liked post by chainsaw On thread : Rifle Scope
    A 3-9x42 or similar would be a good option for your hunting, plenty of older quality scopes around that you pick up for $300 -$600 or you could spend a bit more for a 2-10x or 3-12x or 3-15x. If you...
    Liked On: 26-09-2023, 08:27 PM
  4. Nugget connaisseur
    Nugget connaisseur liked post by chainsaw On thread : Rifle Scope
    A 3-9x42 or similar would be a good option for your hunting, plenty of older quality scopes around that you pick up for $300 -$600 or you could spend a bit more for a 2-10x or 3-12x or 3-15x. If you...
    Liked On: 26-09-2023, 07:59 PM
  5. hebe
    hebe liked post by chainsaw On thread : Wanaka roar blocks - chamois?
    Reasonable numbers in some blocks, they like steep gnarly country
    Liked On: 26-09-2023, 12:50 PM
  6. EmpireSafaris
    EmpireSafaris liked post by chainsaw On thread : Empty brass on plane
    It must not be “loose” or you’ll be toast
    Liked On: 23-09-2023, 11:45 AM
  7. SixtyTen
    SixtyTen liked post by chainsaw On thread : 6.5 prc load development - Seeking wisdom
    Both pills will work very well at range, but not really suited to close up. You run the risk of blow up on the shoulder. Choose a projectile like 140gn HotCore or Partition or bonded pill for close...
    Liked On: 22-09-2023, 11:38 PM
  8. dannyb
    dannyb liked post by chainsaw On thread : Low-vember tahr hunt
    Yes, that’s an option so long as not too spendie
    Liked On: 22-09-2023, 08:59 AM
  9. Micky Duck
    Micky Duck liked post by chainsaw On thread : Bullet for 7mm Rem
    150gn Partitions for up close out to 300yd (or 400 for that matter. 162 ELDMs or 168 Berger VLDs for 300+.
    Liked On: 13-09-2023, 09:26 PM
  10. gqhoon
    gqhoon liked post by chainsaw On thread : Ballistic truing conundrum
    SAUM 162 ELDM RL26 scope DOPE update An update on previous posts, chasing down a difference of +1moa at 625 yards. Ballistic solvers predicted a 10moa come up, compared to my dialed come up of 9moa...
    Liked On: 12-09-2023, 08:43 AM
  11. rossi.45
    rossi.45 liked post by chainsaw On thread : Ballistic truing conundrum
    SAUM 162 ELDM RL26 scope DOPE update An update on previous posts, chasing down a difference of +1moa at 625 yards. Ballistic solvers predicted a 10moa come up, compared to my dialed come up of 9moa...
    Liked On: 12-09-2023, 08:26 AM
  12. charliehorse
    charliehorse liked post by chainsaw On thread : Ballistic truing conundrum
    SAUM 162 ELDM RL26 scope DOPE update An update on previous posts, chasing down a difference of +1moa at 625 yards. Ballistic solvers predicted a 10moa come up, compared to my dialed come up of 9moa...
    Liked On: 11-09-2023, 10:39 PM
  13. Bowhunta
    Bowhunta liked post by chainsaw On thread : Should I avoid Hornady brass?
    My experience with Hornady brass in magnum caliber is they tend to develop split necks after 1-2 firings. This can be avoided or reduced by annealing. So I would suggest anneal after first firing....
    Liked On: 11-09-2023, 01:46 PM
  14. Longrun
    Longrun liked post by chainsaw On thread : Should I avoid Hornady brass?
    My experience with Hornady brass in magnum caliber is they tend to develop split necks after 1-2 firings. This can be avoided or reduced by annealing. So I would suggest anneal after first firing....
    Liked On: 11-09-2023, 01:19 PM
  15. stagstalker
    stagstalker liked post by chainsaw On thread : To shoot a tahr you gotta be a tahr
    Epic ! That’s stupid steep country
    Liked On: 10-09-2023, 07:45 PM

24-08-2020


22-08-2020


20-08-2020


17-08-2020


15-08-2020


08-08-2020


07-08-2020


04-08-2020


20-07-2020


16-07-2020


13-07-2020


10-07-2020


07-07-2020


12-06-2020


09-06-2020


05-06-2020


03-06-2020



26-12-2018


Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!