Friwi
Member

2290 Likes

Page 6 of 153 First 123456789101112131415161718192056106 ... Last

• Jump to page:

1. 
   caberslash liked post by Friwi On thread : Is the new 7mm PRC a lemon ?

   The tikka long action mag works very well too :-) not even need to replace the bottom metal or to put it into a chassis …

   Liked On: 16-02-2024, 08:36 AM

2. 
   Ana liked post by Friwi On thread : Seeking Hunting Grounds Advice around Auckland

   Welcome to the forum. I am not in Auckland so I can’t really help. But I m sure someone with raise their hand and help you.

   Liked On: 15-02-2024, 06:44 PM

3. 
   veitnamcam liked post by Friwi On thread : Is the new 7mm PRC a lemon ?

   Funny , I remember the 7mm 162 amax of 2003 that would vaporise in mid air when launched from a 7mm weatherby … Talking about weatherby, with their long freebore, it might be possible to set the 175...

   Liked On: 15-02-2024, 02:54 AM

4. 
   dannyb liked post by Friwi On thread : Is the new 7mm PRC a lemon ?

   Funny , I remember the 7mm 162 amax of 2003 that would vaporise in mid air when launched from a 7mm weatherby … Talking about weatherby, with their long freebore, it might be possible to set the 175...

   Liked On: 14-02-2024, 07:22 PM

5. 
   TakaRat liked post by Friwi On thread : Wairere Fall's Hunting

   I have shots 3 deer overthe years in the clearing you are talking about. They are constantly been checked out by hunters. So any time a new deer pops up it pretty much get shot. You just have to be...

   Liked On: 13-02-2024, 08:17 PM

6. 
   Micky Duck liked post by Friwi On thread : 1000 yard gong

   If you can tie a few 1 meter long rubans to some poles along the way you will learn a bit more about the influence of the wind and when to take the shot .

   Liked On: 12-02-2024, 07:53 PM

7. 
   Nathan F liked post by Friwi On thread : 308 bush pig loads

   The 150 sst never shot well in my kimber :-( all right for stuff within 50 m( I shot a sow at 25m with them) but at 100m it was up to 2.5” group. The 168gr sierra match kings on the other hand are...

   Liked On: 11-02-2024, 07:57 AM

8. 
   caberslash liked post by Friwi On thread : Rem 700 magazine well

   No, that is probably because the spacer has not been put on from the top . There are two tabs on the top which stop it from falling down. But sometime you can still hear the spacer rattling

   Liked On: 11-02-2024, 12:04 AM

9. 
   erniec liked post by Friwi On thread : Rem 700 magazine well

   No, that is probably because the spacer has not been put on from the top . There are two tabs on the top which stop it from falling down. But sometime you can still hear the spacer rattling

   Liked On: 10-02-2024, 09:36 PM

10. 
    Shearer liked post by Friwi On thread : Tropical fishing. Looking for suggestions.

    Australia coast would be full of crocs? Nah?

    Liked On: 09-02-2024, 07:22 AM

11. 
    -BW- liked post by Friwi On thread : 9.3x62 loading

    Take a look at 9.3x62 journal. Heaps of loads , and history on the cartridge. The South African Author is actually based in Auckland now. You can buy his book as an e book. Well worth it. 242910

    Liked On: 08-02-2024, 03:43 PM

12. 
    Dazzh liked post by Friwi On thread : A gunsmith question - head spacing.

    Other solution, is fitting a custom recoil lug , slightly thicker. The benefit is that a bit of truing work can be done on the action face, bolt face and lug abutment/ contact if required . Final ...

    Liked On: 08-02-2024, 10:11 AM

13. 
    6x47 liked post by Friwi On thread : A gunsmith question - head spacing.

    Other solution, is fitting a custom recoil lug , slightly thicker. The benefit is that a bit of truing work can be done on the action face, bolt face and lug abutment/ contact if required . Final ...

    Liked On: 07-02-2024, 09:19 PM

14. 
    chainsaw liked post by Friwi On thread : A gunsmith question - head spacing.

    Other solution, is fitting a custom recoil lug , slightly thicker. The benefit is that a bit of truing work can be done on the action face, bolt face and lug abutment/ contact if required . Final ...

    Liked On: 07-02-2024, 08:53 PM

15. 
    Maca49 liked post by Friwi On thread : A gunsmith question - head spacing.

    Other solution, is fitting a custom recoil lug , slightly thicker. The benefit is that a bit of truing work can be done on the action face, bolt face and lug abutment/ contact if required . Final ...

    Liked On: 07-02-2024, 08:48 PM

Page 6 of 153 First 123456789101112131415161718192056106 ... Last

• Jump to page: