grandpamac
Member

4758 Likes

Page 132 of 318 First ... 3282118119120121122123124125126127128129130131132133134135136137138139140141142143144145146182232 ... Last

• Jump to page:

1. 
   techno retard liked post by grandpamac On thread : 300 PRC thoughts for a new guy

   Another one for the .308. Proven performance. Plenty of ammo and components. Easy to load for, no special powders needed. Get the long range flashy stuff later if you find you need it. With the...

   Liked On: 08-12-2022, 07:35 AM

2. 
   techno retard liked post by grandpamac On thread : NZDA.

   Greetings All, I am a member of both Hastings (Superanuant) and Taupo (Associate) NZDA. I live just out of Hastings but joined Taupo as an Affilliate after the Roys Hill Range closed in the late...

   Liked On: 06-12-2022, 09:40 PM

3. 
   Ruger7mm liked post by grandpamac On thread : Round 2

   Greetings 300wsm for life, Hodgdons only recommends AR2206H (H4895) for loads reduced below starting loads. They don't even recommend IMR4895 having found the ADI powder worked better. 500 grams of...

   Liked On: 05-12-2022, 03:40 PM

4. 
   300wsm for life liked post by grandpamac On thread : Round 2

   Greetings All, A couple of light .308W loads that you may want to consider for the young hunters. 38 grains of AR2206H behind a Hornady 150 grain Interlock chronographed at 2,380 fps from a 22"...

   Liked On: 05-12-2022, 12:40 PM

5. 
   Micky Duck liked post by grandpamac On thread : 556/223 brass

   Greetings All, Relentless scrounging has resulted in a large supply of once fired .223 brass. Weighing the brass I found most of it fell into two groups one averaging 94 grains and the other 97...

   Liked On: 01-12-2022, 06:13 PM

6. 
   Mooseman liked post by grandpamac On thread : 556/223 brass

   Greetings Proudkiwi, A very fair question. I think it is just that I like doing it. My experience is that the military brass is excellent quality, at least as good as most of the US commercial...

   Liked On: 01-12-2022, 03:45 PM

7. 
   techno retard liked post by grandpamac On thread : 556/223 brass

   Greetings Proudkiwi, A very fair question. I think it is just that I like doing it. My experience is that the military brass is excellent quality, at least as good as most of the US commercial...

   Liked On: 01-12-2022, 01:51 PM

8. 
   7mm Rem Mag liked post by grandpamac On thread : 556/223 brass

   Greetings All, Relentless scrounging has resulted in a large supply of once fired .223 brass. Weighing the brass I found most of it fell into two groups one averaging 94 grains and the other 97...

   Liked On: 01-12-2022, 10:36 AM

9. 
   7mm Rem Mag liked post by grandpamac On thread : 556/223 brass

   Greetings All, Weighing the cases or a sample of them will allow you to group the similar ones together. I have done quite a bit of this so will share my findings tomorrow. GPM.

   Liked On: 01-12-2022, 07:47 AM

10. 
    Borris liked post by grandpamac On thread : Full length sizing issue

    Greetings again, Fired Factory cases come out of my chamber at 1.631" And handloads at 1.6315". Sized in a Redding body die hard down on the shell holder they measure 1.621" so I suspect your die is...

    Liked On: 29-11-2022, 09:38 AM

11. 
    rewa liked post by grandpamac On thread : Resurgence of interest in the old "Three Oh"?

    I broke down some of the later boxer primed CAC cartridges for the components a while back. Much of the powder had clumped badly and there was light corrosion inside the cases. I fired the primers,...

    Liked On: 27-11-2022, 08:16 PM

12. 
    rewa liked post by grandpamac On thread : Resurgence of interest in the old "Three Oh"?

    Greetings Bumblefoot and All, I've found the Lee Loader is ideal for neck sizing the .303 as it doesn't over size the neck. I prime them with a Lee hand tool. I have, in the interests of science...

    Liked On: 27-11-2022, 08:08 PM

13. 
    rewa liked post by grandpamac On thread : Resurgence of interest in the old "Three Oh"?

    Greetings bumblefoot and all, A nice calm day today so I finally got to do a rough sight in on my latest new to me .303. As reported earlier in another thread the rifle was given to me by a friend...

    Liked On: 27-11-2022, 07:56 PM

14. 
    Moa Hunter liked post by grandpamac On thread : Info on .270 load data using Hodgdon Superperformance powder and 130gr projectiles

    Greetings Dawg, I note that Hodgdons has a max of 54.3 grains of AR2209 for 3,012 fps at 50,500 CUP in a 24" barrel. Your 18" barrel would lose 25fps maybe 30 fps per inch or 150 fps to 180 fps...

    Liked On: 27-11-2022, 05:59 PM

15. 
    Growlybear liked post by grandpamac On thread : A Poor Man's Rangefinder

    Greetings All, I don't have any beef with having and using range finders. I have one myself and it was great for telling us how far away the cardboard deer was last week. The OP was aimed at those...

    Liked On: 27-11-2022, 04:08 PM

Page 132 of 318 First ... 3282118119120121122123124125126127128129130131132133134135136137138139140141142143144145146182232 ... Last

• Jump to page: