This mod, together with the Lumley Arms spring kit, will eliminate "creep" totally! There is a very informative article on the LA101 trigger assembly if you have a look in the top right hand corner...
Liked On: 20-09-2023, 10:10 PM
This mod, together with the Lumley Arms spring kit, will eliminate "creep" totally! There is a very informative article on the LA101 trigger assembly if you have a look in the top right hand corner...
Liked On: 15-09-2023, 12:17 PM
I had this built in the US last year - Shipped in September and finally arrived at my local dealer's. I just finished setting it up ready for a run next week. The builder has already test fired it...
Liked On: 16-06-2023, 10:55 PM
I had this built in the US last year - Shipped in September and finally arrived at my local dealer's. I just finished setting it up ready for a run next week. The builder has already test fired it...
Liked On: 16-06-2023, 10:53 PM
Primal Rights & TS Customs from South Dakota put this together for me. Rim X action Benchmark 26" MTU profile 3 groove with Primal Rights 1.5 degree chamber (Works well with my preferred SK/Lapua...
Liked On: 16-06-2023, 10:47 PM
I had this built in the US last year - Shipped in September and finally arrived at my local dealer's. I just finished setting it up ready for a run next week. The builder has already test fired it...
Liked On: 16-06-2023, 07:19 PM
I had this built in the US last year - Shipped in September and finally arrived at my local dealer's. I just finished setting it up ready for a run next week. The builder has already test fired it...
Liked On: 16-06-2023, 06:02 PM
I had this built in the US last year - Shipped in September and finally arrived at my local dealer's. I just finished setting it up ready for a run next week. The builder has already test fired it...
Liked On: 16-06-2023, 05:59 PM
I had this built in the US last year - Shipped in September and finally arrived at my local dealer's. I just finished setting it up ready for a run next week. The builder has already test fired it...
Liked On: 16-06-2023, 05:54 PM
Tentman & I were chatting about rimfires and the LA101 was mentioned. My wife shot the attached target with her Lithgow yesterday - 50 metres outdoors with some twitchy wind increasing steadily all...
Liked On: 02-04-2023, 07:14 AM
I only use quality one piece rods, good fitting bronze brushes and jags (ALWAYS a bore guide) to "deep clean" rifle bores. However, I do fire a lot of rounds at the range and always run a couple...
Liked On: 10-08-2022, 08:52 PM
I only use quality one piece rods, good fitting bronze brushes and jags (ALWAYS a bore guide) to "deep clean" rifle bores. However, I do fire a lot of rounds at the range and always run a couple...
Liked On: 10-08-2022, 10:58 AM
Not necessarily a "rimfire" scope but if you want to eliminate the variables when shooting paper with a 22LR, adjustable parallax is essential IME...Preferably something that goes down to 25 yards or...
Liked On: 06-08-2022, 08:49 PM
Not necessarily a "rimfire" scope but if you want to eliminate the variables when shooting paper with a 22LR, adjustable parallax is essential IME...Preferably something that goes down to 25 yards or...
Liked On: 06-08-2022, 06:02 PM
For what it's worth, my wife and I are in our 70's. We had a T36 FCH DOT on an Anschutz 1710 and it went down the road pretty quickly - Neither of us could see the reticle well and by the end of a...
Liked On: 18-03-2022, 06:40 PM