jpurdon
Member

265 Likes

Page 14 of 18 First 123456789101112131415161718 Last

• Jump to page:

1. 
   jpurdon liked post by Micky Duck On thread : 3.1" eye relief too small?

   wait and get a loopy......there have been shed loads come up here over the last 3 months.....

   Liked On: 21-05-2022, 02:00 PM

2. 
   jpurdon liked post by Moa Hunter On thread : Thoughts on this rifle/deal? Remington700 7mm-08

   jpurdon , I have a 270. After reading what you are wanting to do I wouldnt muck round, buy philipo's 6.5 prc It will do it all and you will have it for life....

   Liked On: 14-05-2022, 10:38 AM

3. 
   jpurdon liked post by Happy Jack On thread : Head torches

   Just seen that Sarvo is going to be stocking Olight torches and head torches.

   Liked On: 08-03-2022, 09:38 PM

4. 
   jpurdon liked post by Gibo On thread : Thanks Leupold!

   Buy another rifle to put it on duh!

   Liked On: 23-09-2021, 05:30 PM

5. 
   jpurdon liked post by Tui4Me On thread : Best way to sharpen Mercator Stainless?

   I do the same as you but without the 4x2. Lansky stone kit followed by two light strokes on each side with a very fine butcher steel. I sharpen until the entire blade area will grip firmly on a...

   Liked On: 08-09-2021, 09:50 PM

6. 
   jpurdon liked post by Pixie Z On thread : Best way to sharpen Mercator Stainless?

   I took two Mercators with me to the UK, but never had any issues. Like you it never occurred to me that it could be a problem, I'm just used to having one around as a utility knife. Will often have...

   Liked On: 08-09-2021, 09:45 PM

7. 
   jpurdon liked post by Dundee On thread : Best way to sharpen Mercator Stainless?

   I use a fine stone and follow up with a few strokes on the diamond steel.I paid $89 about a month ago the true slozenger mercator made in germany. 178070178071178072

   Liked On: 08-09-2021, 09:44 PM

8. 
   jpurdon liked post by T.FOYE On thread : Any spearfisherman on the forum?

   Started spearing back in 1997 and have kinda done it on and off. Not much of late. I came to NZ expecting idiotically large kingies and i wasn't disappointed. The Aldermans are unreal If you see a...

   Liked On: 08-09-2021, 09:20 PM

9. 
   jpurdon liked post by oneshot On thread : Any spearfisherman on the forum?

   I'm mad keen at spearfishing, I probably get in the water as much as I do in the bush.

   Liked On: 08-09-2021, 09:19 PM

10. 
    jpurdon liked post by flock On thread : Best way to sharpen Mercator Stainless?

    Always struggled to keep my Mercator sharp, own several used to put a very fine edge on it with an oil stone. Have been using a lansky knife sharping system and for the Mercator the middle stoning...

    Liked On: 08-09-2021, 05:05 PM

11. 
    jpurdon liked post by 40mm On thread : Best way to sharpen Mercator Stainless?

    Only thing with rust is that it leaves 'craters' which will forever be a part of the finished edge. Unless you can polish ALL the rust pitting out then it will never be as sharp as it could...

    Liked On: 07-09-2021, 06:59 PM

12. 
    jpurdon liked post by outdoorlad On thread : Best way to sharpen Mercator Stainless?

    Best way is to send it to Shelley with a prepaid return envelope and $10

    Liked On: 07-09-2021, 04:02 PM

13. 
    jpurdon liked post by 40mm On thread : Best way to sharpen Mercator Stainless?

    Best way I have found (but not the only way) is to replace it with a carbon steel blade! I have an Opinel #8, only downside is it can be a bastard to open if not used for a while. I cut some of...

    Liked On: 07-09-2021, 03:59 PM

14. 
    jpurdon liked post by bigbear On thread : RST Hunters Club - New Series

    The Hunters Club how did the two young fellas get on? They would have been pretty excited getting the ride in and opportunity to meet you guys.

    Liked On: 07-09-2021, 10:06 AM

15. 
    jpurdon liked post by ANOTHERHUNTER On thread : Any spearfisherman on the forum?

    Pretty keen on the spearfishing , spending more time teaching the kids how to do it lately which is good fun.

    Liked On: 06-09-2021, 08:03 PM

Page 14 of 18 First 123456789101112131415161718 Last

• Jump to page: