Pommy
Member

1393 Likes

Page 65 of 93 First ... 155152535455565758596061626364656667686970717273747576777879 ... Last

• Jump to page:

1. 
   Shamus_ liked post by Pommy On thread : Getting ES down with 223

   Primer Shootout PPU brass, fireformed, annealed, trimmed, uniformed, necks brushed. 55gn Speer Gold Dot, 25.8gn BM8208, 2.300" COL. Federal GM205M 3280 DNR 3234 3228 3223 3232

   Liked On: 21-07-2021, 07:16 AM

2. 
   ebf liked post by Pommy On thread : Getting ES down with 223

   Primer Shootout PPU brass, fireformed, annealed, trimmed, uniformed, necks brushed. 55gn Speer Gold Dot, 25.8gn BM8208, 2.300" COL. Federal GM205M 3280 DNR 3234 3228 3223 3232

   Liked On: 21-07-2021, 02:41 AM

3. 
   Carpe Diem liked post by Pommy On thread : N565 & R26 in 6.5PRC - anyone using it?

   Gold dots should go mint at those ranges given the speeds. I've been really happy with their repeatedly good performance in 223.

   Liked On: 20-07-2021, 05:43 PM

4. 
   Steelisreal liked post by Pommy On thread : Getting ES down with 223

   Same load (55gn Gold Dot, 26gn 8208, 2.300") tried with different brass: PPU (fireformed, annealed, FL sized, trimmed, uniformed) 3245 3265 3293 3268 3293 3282

   Liked On: 20-07-2021, 11:36 AM

5. 
   Tentman liked post by Pommy On thread : Getting ES down with 223

   Same load (55gn Gold Dot, 26gn 8208, 2.300") tried with different brass: PPU (fireformed, annealed, FL sized, trimmed, uniformed) 3245 3265 3293 3268 3293 3282

   Liked On: 20-07-2021, 11:01 AM

6. 
   ebf liked post by Pommy On thread : Getting ES down with 223

   Same load (55gn Gold Dot, 26gn 8208, 2.300") tried with different brass: PPU (fireformed, annealed, FL sized, trimmed, uniformed) 3245 3265 3293 3268 3293 3282

   Liked On: 20-07-2021, 10:29 AM

7. 
   Hunter_Nick liked post by Pommy On thread : Accuracy expectations

   Defo. Whilst the bush thing probably doesn't have any negative impacts if done properly, clearly something is negatively impacting the groups so that's got to be near the top of the list of likely...

   Liked On: 16-07-2021, 03:42 PM

8. 
   ebf liked post by Pommy On thread : Getting ES down with 223

   I think the consistency I get with the 69's demonstrates that there's no fault with the rifle. Had some new lapua brass to fireform so chucked together another quick load this evening (1c at the...

   Liked On: 12-07-2021, 09:46 PM

9. 
   Micky Duck liked post by Pommy On thread : Getting ES down with 223

   Thanks for the offer. Let's put a pin in that. I'll do another one or two tests and the best load can go into a primer shootout.

   Liked On: 10-07-2021, 09:58 PM

10. 
    Micky Duck liked post by Pommy On thread : Getting ES down with 223

    Round 2... 25.6gn Benchmark 2 Skipped the control group with virgin brass, as the first round showed very little difference between new and fireformed (all else being equal)... Plus I was feeling...

    Liked On: 10-07-2021, 09:57 PM

11. 
    Micky Duck liked post by Pommy On thread : Getting ES down with 223

    Shall apply some graphite to the necks for the brushed cases too.

    Liked On: 10-07-2021, 09:56 PM

12. 
    Micky Duck liked post by Pommy On thread : Getting ES down with 223

    Yep, everything's pretty similar. With those Nosler bullets being quite long, seating them out to 2.350" actually gets them pretty close to the rifling. I am going to try the nylon brush as per...

    Liked On: 10-07-2021, 09:56 PM

13. 
    ebf liked post by Pommy On thread : Getting ES down with 223

    Round 2... 25.6gn Benchmark 2 Skipped the control group with virgin brass, as the first round showed very little difference between new and fireformed (all else being equal)... Plus I was feeling...

    Liked On: 10-07-2021, 09:04 PM

14. 
    Fisherman liked post by Pommy On thread : .223 bullet deflection from twigs and branches

    There's an old doco on YT called deadly weapons, firearms and firepower. Towards the end of part 3 here (https://youtu.be/QlTSS-WFpkg) he does some brush testing and everything fairs pretty similarly.

    Liked On: 09-07-2021, 08:54 PM

15. 
    Tahr liked post by Pommy On thread : N565 & R26 in 6.5PRC - anyone using it?

    I'm getting 2930 with 147's in a 25.5" barrel. Super mild load of AR2217 (to hopefully extend the barrel life) and a CCI 250. Plenty of room to push harder. Have tried Re26 and there's a nice load...

    Liked On: 09-07-2021, 08:45 PM

Page 65 of 93 First ... 155152535455565758596061626364656667686970717273747576777879 ... Last

• Jump to page: