rs200nz
Member

209 Likes

Page 1 of 14 1234567891011121314 Last

• Jump to page:

1. 
   rs200nz liked post by jackson21 On thread : 303 174gr with 2206H

   Chronied some Greek last month, that stuff was honking in 2480-2500 fps range. Put about 50 odd of mixed 303 with some reloads downrange on a hot day in a tee-shirt. Was fun until towards the...

   Liked On: 10-01-2023, 02:46 PM

2. 
   rs200nz liked post by Tussock On thread : Forum shooting challenge: The under 500 500

   Here is the challenge. You must post here the following. The purchase of a scope and rifle combination for less than $500 Work done on the rifle after the purchase of the rifle must stay withing...

   Liked On: 11-03-2019, 08:36 PM

3. 
   rs200nz liked post by dogmatix On thread : Hushpower AR

   30 cal AR barrel will normally have a 5/8-24 muzzle thread.

   Liked On: 28-02-2019, 02:51 PM

4. 
   rs200nz liked post by Tommy On thread : Ruger 77 .223 MAE Full over barrel hard to remove

   Is that a recent thing? My dealings with them were only a couple of months ago.

   Liked On: 06-04-2018, 08:36 AM

5. 
   rs200nz liked post by Tommy On thread : Ruger 77 .223 MAE Full over barrel hard to remove

   Take to MAE, they are bloody great for after sales service, even if you weren't the original purchaser. Found that out just recently. They are in East Tamaki.

   Liked On: 05-04-2018, 07:36 PM

6. 
   rs200nz liked post by WallyR On thread : Ruger 77 .223 MAE Full over barrel hard to remove

   rs200nz Looks OK to me - clockwise from pics viewpoint behind (Behring) rifle. Most likely carbon has gotten into threads and jammed the suppressor on. Lazy previous owner :pissed off: methinks.

   Liked On: 05-04-2018, 07:36 PM

7. 
   rs200nz liked post by Boar Freak On thread : Not worth the hassle...

   Grandad's single shot Gecado .22lr whitout a bolt because he can't remember where he put it 9 years ago. That's a fairly safe firearm in my opinion.

   Liked On: 08-03-2018, 01:48 PM

8. 
   rs200nz liked post by Tommy On thread : Not worth the hassle...

   I sense this is a trick question....

   Liked On: 08-03-2018, 01:48 PM

9. 
   rs200nz liked post by 308 On thread : Not worth the hassle...

   onya

   Liked On: 07-03-2018, 07:57 AM

10. 
    rs200nz liked post by Tommy On thread : Not worth the hassle...

    There is no requirement as to size, if you can fit the rifle in there in two bits, that is good enough. Tell him to get fucked and keep your endorsement EDIT: And there's also nothing requiring...

    Liked On: 05-03-2018, 01:56 PM

11. 
    rs200nz liked post by Maca49 On thread : 2017 Toby memorial.

    Where we going?

    Liked On: 11-03-2017, 07:52 AM

12. 
    rs200nz liked post by Moutere On thread : Quick AR15 Garage build

    Terrific photos.

    Liked On: 31-08-2015, 02:01 PM

13. 
    rs200nz liked post by steven On thread : Quick AR15 Garage build

    maybe like the chrono's we should have a forum AR15 assembly block set? Seems a bit crazy to spend $150~$200 each.

    Liked On: 31-08-2015, 02:01 PM

14. 
    rs200nz liked post by time out On thread : building a bivy

    My mate (in the pic) built this one about half way up Takapari Ridge (Pohangina) in the late 50s - but after the road went in we just camped beside the car a bit further up in the leatherwood ...

    Liked On: 28-07-2015, 10:20 PM

15. 
    rs200nz liked post by Munsey On thread : Stolen .338L in Ashburton

    Farrrrrk not nice in the wrong hands . Mind you they would shit themselves if they cut that down and fire it first time without ear protection .

    Liked On: 23-07-2015, 06:20 PM

Page 1 of 14 1234567891011121314 Last

• Jump to page: