shooternz
Member

904 Likes

Page 6 of 61 First 123456789101112131415161718192056 ... Last

• Jump to page:

1. 
   shooternz liked post by dannyb On thread : primers...what is softest/easiest to ignite???

   Might be an issue with the firing pin or spring ? You may have the same issue no matrer what primers you use :(

   Liked On: 17-07-2022, 08:23 PM

2. 
   shooternz liked post by Kelton On thread : Split brass

   Case head separation can be cause by over sizing them

   Liked On: 11-07-2022, 11:16 PM

3. 
   shooternz liked post by Three O'Three On thread : Pistol powders in rifles question

   Also looking at this. It has 26gn of h414 and 24gn of h4895 listed. To my knowledge 2208 having a burn rate in-between the two, one would assume 25g of 2208 would also work? Which I tried with good...

   Liked On: 10-07-2022, 02:38 PM

4. 
   shooternz liked post by The bomb On thread : Cast 151 gr feeding ok in a Tikka ?

   Didn’t feed well in my A7,went to the pointed 170g cast problem solved but not slot of expansion,those 151g open up real well when I single fed them.

   Liked On: 08-07-2022, 03:15 PM

5. 
   shooternz liked post by NewbieZAR On thread : Cast 151 gr feeding ok in a Tikka ?

   I just load them to the crimp ring and then crimp them.

   Liked On: 08-07-2022, 03:14 PM

6. 
   shooternz liked post by Marty Henry On thread : Pistol powders in rifles question

   Page from my 43rd edition lyman book. In their powder equivalents table ADI list AP 70n as being equivalent to unique and 4197 as approximating 2207 so you get the idea. It doesn't need a filler....

   Liked On: 08-07-2022, 03:09 PM

7. 
   shooternz liked post by Micky Duck On thread : 400gr 44magnum loads

   if your current subsonic is already passing through,,upping weight wont help at all....it wont make any bigger hole or transpher anymore energy.... unless you hitting enough bone to slow it down/stop...

   Liked On: 07-07-2022, 09:14 PM

8. 
   shooternz liked post by andyanimal31 On thread : Hornardy micojust seating stem

   I have one and works as it should, it's not a redding comp seater but you probably can't shoot that well to tell the difference! Sent from my SM-A226B using Tapatalk

   Liked On: 29-06-2022, 07:40 PM

9. 
   shooternz liked post by Pauli On thread : Where to start

   mattstr got a set of Hornady balance beam scales and a Hornady powder dispenser you can have to help you on your way. Just pay postage ($15 max). 199739 NB. Powder dispenser does not have a...

   Liked On: 20-06-2022, 12:31 PM

10. 
    shooternz liked post by garyp On thread : Where to start

    I am in Napier. As a retired person I am very happy to let you use my gear and componants - powder , primers , projectiles etc and show you how to do it. Cheers, Gary.

    Liked On: 20-06-2022, 12:27 PM

11. 
    shooternz liked post by dannyb On thread : Incremental load test anomalies

    Find a stable es charge and providing it shoots good groups varify velocity by shooting at longer ranges and calculate velocity by using the drop.

    Liked On: 06-06-2022, 10:36 PM

12. 
    shooternz liked post by Ross Nolan On thread : Norma Vulkan projectiles.

    I've used them in 30 cal, 8mm and 6.5mm The are accurate, hold together well and open up fairly quickly, but are not at all aerodynamic. Nowadays I'm using Norma Oryx as a bush load in 7mm and...

    Liked On: 01-06-2022, 01:12 PM

13. 
    shooternz liked post by Micky Duck On thread : Improving 45-70 ammo with a mandrel

    I believe you are over thinking it....and recoil....means you are pushing things hard...45grns of 2208 is good load behind 400grn cast....its stout but not rattle your teeth hot.... there used to be...

    Liked On: 22-05-2022, 11:50 AM

14. 
    shooternz liked post by akaroa1 On thread : Improving 45-70 ammo with a mandrel

    Re the next tension You are assuming the tension you experienced pulling the bullets is the same tension when the bullet is being released up the barrel I wouldn't assume that because the...

    Liked On: 22-05-2022, 11:47 AM

15. 
    shooternz liked post by Marty Henry On thread : beeswax lube and spay painting bullets

    Stand a whole bunch of projectiles upright in a flat pan melt your lube and pour it into the pan till it's level with the top grease groove and leave it to cool. Cut the bullets out with a "cookie...

    Liked On: 22-05-2022, 11:26 AM

Page 6 of 61 First 123456789101112131415161718192056 ... Last

• Jump to page: