shooternz
Member

904 Likes

Page 8 of 61 First 1234567891011121314151617181920212258 ... Last

• Jump to page:

1. 
   shooternz liked post by stug On thread : Better accuracy for my 308

   Load up 20 and go hunting. 1” at 100 will be accurate enough out to 300yds or so if taking shoulder shots on deer.

   Liked On: 19-01-2022, 07:17 PM

2. 
   shooternz liked post by Cigar On thread : ADI 2207 and short barrel 308

   ADI have the data for 2207 with light bullets, and you can get hold of it, so go for it.

   Liked On: 14-01-2022, 11:26 PM

3. 
   shooternz liked post by Bryan Austin On thread : 44-40 Reloading/Shooting

   I made a case canular tool from a small pipe cutter just like Carlson Highway did...no "teeth" needed. The case is thin and easily manipulated. Here is a photo of a case I did a while back...it is...

   Liked On: 12-01-2022, 11:23 AM

4. 
   shooternz liked post by Bryan Austin On thread : 44-40 Reloading/Shooting

   Here is a bullet I had custom made by Accurate Molds. It is simply a modified Lyman 427098. This photo shows both the 43-214A and a JSP crimped with a Redding Profile Crimp Die 187429187428 ...

   Liked On: 12-01-2022, 11:21 AM

5. 
   shooternz liked post by SixtyTen On thread : Casting for an SMLE

   I ended up making my own copy of a Lyman M die as well as a 0.318 sizing stem. With my projectiles being around 0.3190 after powdercoating, there was no way they would seat in a standard sized neck....

   Liked On: 12-01-2022, 11:17 AM

6. 
   shooternz liked post by rossi.45 On thread : Cast bullet Varminting / Medium game Project

   pages were taken from this book . . 687 pages has a big section on the American Civil War with lots of mentions of the Whitworth and the men and their exploits 186641

   Liked On: 28-12-2021, 10:39 AM

7. 
   shooternz liked post by gundoc On thread : Casting for an SMLE

   The groove diameter is not overly significant if you are casting as the bullet will upset to the groove when it is fired. The bullet material displaced by the lands will swage into the grooves. A...

   Liked On: 14-12-2021, 12:21 AM

8. 
   shooternz liked post by johnd On thread : Who would still buy MOA over MIL and why?

   Places where the target system scores and relates to MOA such as FTR. Trust me converting Mils to MOA when someone is giving you windages and elevation in MOA and you are converting it in your head...

   Liked On: 08-12-2021, 10:51 AM

9. 
   shooternz liked post by Sideshow On thread : 303 vs 308

   https://auctions.holtsauctioneers.com/asp/fullCatalogue.asp?salelot=S0122+++4578C&refno=++168012&saletype= ;):P

   Liked On: 05-12-2021, 01:47 PM

10. 
    shooternz liked post by Marty Henry On thread : Suppressor and load dev

    I think Jhon has the right idea. I feel that for a hunting rifle the idea of developing an ideal load is actually pretty pointless if anything you chuck down the barrel prints about 1 moa anyhow....

    Liked On: 15-11-2021, 01:17 PM

11. 
    shooternz liked post by gundoc On thread : Cartridge suggestions

    .308 or .30/06 will fill your needs nicely with a comprehensive range of projectiles available in the 150 - 180 grain range.

    Liked On: 11-11-2021, 03:22 PM

12. 
    shooternz liked post by Cigar On thread : Crimping 308win subsonics?

    I lightly crimp my subsonics. I use Lyman dies and the seating die can be set to give a roll crimp.

    Liked On: 09-11-2021, 01:07 PM

13. 
    shooternz liked post by WilliamJackson1961 On thread : Screwdriver advice

    Brownell's Magna-Tip pieces are the greatest. These are created in the United States and are of the highest quality available. They have a wider range of sizes than anybody else, and you seldom...

    Liked On: 04-11-2021, 07:44 PM

14. 
    shooternz liked post by ebf On thread : Screwdriver advice

    If you have slotted screws (lever actions...) on the firearms you want to work on, make sure you get a decent set with hollow ground slotted bits.

    Liked On: 04-11-2021, 07:43 PM

15. 
    shooternz liked post by Marty Henry On thread : Ban on using jacketed ammo on steel plates?

    The above should be mitigated by target angle and sand trap if needed.

    Liked On: 04-11-2021, 07:38 PM

Page 8 of 61 First 1234567891011121314151617181920212258 ... Last

• Jump to page: