Walker
Member

218 Likes

Page 7 of 15 First 123456789101112131415 Last

• Jump to page:

1. 
   mikee liked post by Walker On thread : Purchasing a rifle barrel in the USA?

   You will require a export permit ($200us) to bring a barrel out of the states.

   Liked On: 14-11-2019, 07:31 AM

2. 
   A330driver liked post by Walker On thread : Purchasing a rifle barrel in the USA?

   You will require a export permit ($200us) to bring a barrel out of the states.

   Liked On: 14-11-2019, 06:47 AM

3. 
   veitnamcam liked post by Walker On thread : Show us your DIY gunsmithing jobs

   Just depends on how much time you want to spend doing the perfect job, 15min,30min, an hour? As you say it's not the space shuttle......, if you can free hand sharpen a drill then its not hard to...

   Liked On: 25-09-2019, 10:03 PM

4. 
   mikee liked post by Walker On thread : Some reasons why it often goes bad.

   You must be bored and feeling quarrelsome today Tussock! the most important thing is the first couple of milli seconds after the firing pin hits the primer and how the action and barrel react to the...

   Liked On: 08-09-2019, 07:45 PM

5. 
   nor-west liked post by Walker On thread : "Weak" Rear Locker Lee Enfield No 4 action vs .300 Win Mag

   30 odd years ago did a 303 I.C.B.M which was a sort of Ackley, could run the 180 grns to 2800fps no worries

   Liked On: 01-09-2019, 11:24 PM

6. 
   muzr257 liked post by Walker On thread : Anyone tried the 6mmSLR?

   Wondering if anyone has tried the round, mainly as I've built a number of 6 remms. 243's, 243 ackley and a couple of brx's for F open. Reading about it looks like the best balance of speed v barrel...

   Liked On: 31-08-2019, 05:11 PM

7. 
   Cordite liked post by Walker On thread : "Weak" Rear Locker Lee Enfield No 4 action vs .300 Win Mag

   30 odd years ago did a 303 I.C.B.M which was a sort of Ackley, could run the 180 grns to 2800fps no worries

   Liked On: 26-08-2019, 10:16 PM

8. 
   csmiffy liked post by Walker On thread : Show us your DIY gunsmithing jobs

   Just depends on how much time you want to spend doing the perfect job, 15min,30min, an hour? As you say it's not the space shuttle......, if you can free hand sharpen a drill then its not hard to...

   Liked On: 15-07-2019, 12:36 PM

9. 
   Boaraxa liked post by Walker On thread : Importing a used scope

   I carried a SKS and 10/22 back to NZ in the 90's no problems.

   Liked On: 08-07-2019, 07:59 PM

10. 
    shooternz liked post by Walker On thread : Ruger #1 303 or 7x57

    Umm wouldn't recommend the 303, they are not the most accurate. Don't know what happened but couldn't get better then 2-3 moa with all types of loads.

    Liked On: 24-05-2019, 07:04 PM

11. 
    Dama dama liked post by Walker On thread : Scope choice

    400m? just get closer. Use a fixed 6x weaver on my 7-08, 140gr 2" high @100, hold top of shoulder anything over 200 to 300

    Liked On: 29-04-2019, 11:28 AM

12. 
    Micky Duck liked post by Walker On thread : Scope choice

    400m? just get closer. Use a fixed 6x weaver on my 7-08, 140gr 2" high @100, hold top of shoulder anything over 200 to 300

    Liked On: 28-04-2019, 08:04 PM

13. 
    Cordite liked post by Walker On thread : Breaking in a new barrel

    Run a patch down with autosol polish on it and give it a good polish, it's mainly to take the edges off any tooling marks left from manufacturing. When its nice and shiney you'll be good to go!...

    Liked On: 23-04-2019, 09:30 PM

14. 
    shooternz liked post by Walker On thread : GRS Riflestocks

    first put a rifle basix trigger on it and bed in original stock to see if its worth the money of the stock. I shoot a howa 223 in F-tr mounted in a GRS beserk but only after getting it to shoot...

    Liked On: 14-04-2019, 04:01 PM

15. 
    janleroux liked post by Walker On thread : GRS Riflestocks

    It went in on the internal pillers very tightly, they are super well made. Not the lightest stock though but value for money.

    Liked On: 14-04-2019, 10:29 AM

Page 7 of 15 First 123456789101112131415 Last

• Jump to page: