caberslash
Member

2734 Likes

Page 68 of 183 First ... 185455565758596061626364656667686970717273747576777879808182118168 ... Last

• Jump to page:

1. 
   caberslash liked post by Beavis On thread : Views on Straight Pull ARs

   Have a GBC rifle that I've been running for a year. Has everything I like about AR15's minus the semi auto part. I find it much more ergonomic to have the charging handle on the right hand side. All...

   Liked On: 23-05-2022, 01:58 AM

2. 
   caberslash liked post by ROKTOY On thread : Hand me down Model 70

   Tea done and a movie on the go, we both set to with the supplied anti rust wipes, going over all treated areas removing the last of the oxide build up and cleaning up the bluing. While I started re...

   Liked On: 23-05-2022, 12:38 AM

3. 
   caberslash liked post by Friwi On thread : Book Download, rifling machines and methods clifford labounty

   Kolbe is now manufacturing chambering reamers .

   Liked On: 22-05-2022, 11:44 PM

4. 
   caberslash liked post by Friwi On thread : Book Download, rifling machines and methods clifford labounty

   Dr Kolbe who ran border barrels in Scotland was a student from cliff labounty. There is a famous picture of them with a few more students including the owner of kreiger barrels as well.

   Liked On: 22-05-2022, 08:24 PM

5. 
   caberslash liked post by rambo-6mmrem On thread : Hunting Scope Magnification

   As others have said It depends what you are doing Some hunters require 15+ Magnification for longer shots The typical hunter a 3-9 or 2-10 perfect If you are going for light waight compact...

   Liked On: 22-05-2022, 07:58 AM

6. 
   caberslash liked post by Rated M for Magnum On thread : Tikka barrel swap

   That's kind of what I was thinking, may need revising :D

   Liked On: 22-05-2022, 06:08 AM

7. 
   caberslash liked post by ROKTOY On thread : Hand me down Model 70

   My Father passed away late last year. Fast forward to early March this year and my lad (12yrs) and I are on my Uncles farm helping to replace wheel bearings on his trailer. Uncle goes over to...

   Liked On: 22-05-2022, 02:12 AM

8. 
   caberslash liked post by Shearer On thread : Hunting Scope Magnification

   2.5-10x42 and 3-15x44.

   Liked On: 21-05-2022, 10:43 AM

9. 
   caberslash liked post by dannyb On thread : Hunting Scope Magnification

   Horses for courses.... For open country I use a 4-20×50 For varminting I uses a 4-16×44 I think for bush hunting anything with a lower end mag of 2 or less would be sweet (currently I don't ownna...

   Liked On: 21-05-2022, 09:32 AM

10. 
    caberslash liked post by Tahr On thread : 223 on deer

    I really pushed the envelope with the 80 Targex and .223 this morning (with a grandson). 330 yards back of the shoulder hit (lung, where I mostly go for with the .223). There was a bit of...

    Liked On: 20-05-2022, 02:04 AM

11. 
    caberslash liked post by tetawa On thread : 270 loads

    Mate found 8lb of the old reclaimed H4831 in a cupboard last month, used to pay $4 a lb for it in the good old days from Reloaders.

    Liked On: 19-05-2022, 07:29 PM

12. 
    caberslash liked post by grandpamac On thread : 270 loads

    Greetings All, It would almost be rude not to try Jack OConnor's often quoted load of 60 grains of 4831 behind the 130 grain projectile even if it was just on paper. Jack worked up this load just...

    Liked On: 19-05-2022, 07:29 PM

13. 
    caberslash liked post by 7mmsaum On thread : 270 loads

    Hornady 140g SST Nosler 140 Ballistic Tip Hornady 145g eldx ADI 2217 powder Federal primers Dead deer out as far as you can see them

    Liked On: 19-05-2022, 07:27 PM

14. 
    caberslash liked post by 7mmsaum On thread : Cartridge advice 2.0 - the 7mm version

    7mm rem mag

    Liked On: 19-05-2022, 11:21 AM

15. 
    caberslash liked post by stug On thread : Cartridge advice 2.0 - the 7mm version

    7wsm is hard to find brass for, unless things have changed markedly. Everyone has 7mm mag brass and is real easy to load for, heaps of factory ammo. 280ai has some brass available, but it can be made...

    Liked On: 19-05-2022, 11:20 AM

Page 68 of 183 First ... 185455565758596061626364656667686970717273747576777879808182118168 ... Last

• Jump to page: