My take on this is .22lr dam good bunny buster, cheap amo. My jump up from it would be 22 hornet / 22-250 or the ones in-between, you can reload them, not so with .22mag and it gets expensive per...
Liked On: 15-02-2021, 10:49 AM
So with that part milled out it`s really starting to look like it will do the job. Fear bit of work to do yet but it`s coming a long, here`s what it looks like so far and the pins are a snug fit so...
Liked On: 13-02-2021, 10:54 PM
Hi Guys, Planning on heading down to Napier for a break when the rush is over and throw the surf casting rod in to the boot. So what`s the fishing like by HW51 were the Ngaruroro and Clive rivers...
Liked On: 11-01-2021, 04:39 PM
Flaming heck ,"I`m only a hobby machinist"` , Hell lad you could build your self a muzzle loading rifle no sweat. Can't wait to see the new rifle stock from the lovely stock pile of wood.
Liked On: 04-01-2021, 09:26 PM
Hell this really needs looking into, with the warm cabinet while the meats getting sunburned could put the homebrew barrel in with fermenting brew and along side the fish smoker!!. Just think, slight...
Liked On: 18-10-2020, 06:25 PM
I just looked in my comeinhandy box, Chain saw bar!!!. :thumbsup: 150951
Liked On: 12-10-2020, 09:08 PM
OK, so having milled out all the centre it needs to be square in the round corners, this was achieved by using a T/C tipped cutter from a saw blade first and then a small HSS square one to finish....
Liked On: 01-10-2020, 10:36 AM
Yes I can get it to do most things, here`s one, It helps with my beer supplies,:) as I use shims to pack things up I have found that ali beer cans cut into strips are the best for this. Different...
Liked On: 27-07-2020, 11:01 PM
Yes I can get it to do most things, here`s one, It helps with my beer supplies,:) as I use shims to pack things up I have found that ali beer cans cut into strips are the best for this. Different...
Liked On: 27-07-2020, 10:08 PM
Yes I can get it to do most things, here`s one, It helps with my beer supplies,:) as I use shims to pack things up I have found that ali beer cans cut into strips are the best for this. Different...
Liked On: 27-07-2020, 09:56 PM
OK, so having milled out all the centre it needs to be square in the round corners, this was achieved by using a T/C tipped cutter from a saw blade first and then a small HSS square one to finish....
Liked On: 27-07-2020, 09:56 PM
So with that part milled out it`s really starting to look like it will do the job. Fear bit of work to do yet but it`s coming a long, here`s what it looks like so far and the pins are a snug fit so...
Liked On: 27-07-2020, 09:54 PM
So just moving along there the lumpy bit has got the chop and have machined a sexy curve at the front so the bottom bits basically finished. So here`s some more learning bit`s Rumpy of how to make...
Liked On: 27-07-2020, 09:44 PM
So the lump is losing a lot of weight, more than I can say about me as my homebrew fridge is in the workshop and I`m good at making tasty loafs of bread. Have setup the lump for what I call fly...
Liked On: 27-07-2020, 09:36 PM
Hi guys, I`ve had this large round lump of 1045 steel and keep stubbing my toes on the dam thing, I`ve been chewing at it like a beaver on and off. As I have the plans for a roller I thought bugger ,...
Liked On: 27-07-2020, 09:33 PM