Rated M for Magnum
Member

391 Likes

Page 2 of 27 First 12345678910111213141516 ... Last

• Jump to page:

1. 
   Rated M for Magnum liked post by akaroa1 On thread : What Have You Loaded Today

   Well I just did a quick count up from my Firearms Registration spread sheet and I reload 25 different calibers ( 4 calibers have multiple rifles in same caliber ) and of those 25 calibers there are 5...

   Liked On: 23-02-2024, 09:05 AM

2. 
   Rated M for Magnum liked post by norsk On thread : What Have You Loaded Today

   How did it sound?

   Liked On: 23-02-2024, 09:01 AM

3. 
   Rated M for Magnum liked post by Old Hand On thread : What powder for 6.5x55?

   I have been using a Tikka 6.5X55 for a number of years now and after a lot of load development I have settled on Norma brass, CCI primers, 46.5 gr of Reloader 17, 135 Berger projectile with a MV of...

   Liked On: 21-02-2024, 11:11 PM

4. 
   Rated M for Magnum liked post by Husky1600#2 On thread : What powder for 6.5x55?

   2209. And the Targex 140gn projectiles are definitely worth a try - accurate, kill well, local, and a tad cheaper than all ELDX/ELDM type projectiles.

   Liked On: 14-02-2024, 10:19 PM

5. 
   Rated M for Magnum liked post by nor-west On thread : What powder for 6.5x55?

   N560 if you can get it.

   Liked On: 14-02-2024, 10:18 PM

6. 
   Rated M for Magnum liked post by Mooseman On thread : What powder for 6.5x55?

   I use both 2209 and 2213sc in my Tikka, another powder well suited to the 6.5’s is Winchester Staball 6.5 has a burn rate similar to 2209.

   Liked On: 14-02-2024, 10:18 PM

7. 
   Rated M for Magnum liked post by blip On thread : What powder for 6.5x55?

   I found my t3 prefered lighter pills. Around the 120gn mark. I use 2209

   Liked On: 14-02-2024, 10:18 PM

8. 
   Rated M for Magnum liked post by Pommy On thread : What powder for 6.5x55?

   Either will be fine. I'd go 2213 just because it's a bit less in demand.

   Liked On: 14-02-2024, 07:10 PM

9. 
   Rated M for Magnum liked post by stagstalker On thread : Is the new 7mm PRC a lemon ?

   I think it would be fair to say the lack of performance in factory ammo applies to any cartridge, new or old. I couldn’t imagine what it must cost to shoot a few rounds and have to buy factory...

   Liked On: 13-02-2024, 04:46 PM

10. 
    Rated M for Magnum liked post by 11mms On thread : Your cartridge of choice.

    242140

    Liked On: 04-02-2024, 10:23 PM

11. 
    Rated M for Magnum liked post by chainsaw On thread : Re-barrel a rifle - trigger event ?

    LOL, plenty of that going on in other threads without me adding fuel to that fire.

    Liked On: 26-01-2024, 02:20 AM

12. 
    Rated M for Magnum liked post by Floundering Around On thread : .270 win load development - Which charge weight do you think?

    Just an update have loaded up 8 rounds of 55.5gr and 56gr. Considering it only has a 22.5" barrel I am pretty happy with sitting just on or just under 3000fps with acceptable accuracy. If they group...

    Liked On: 23-01-2024, 08:58 AM

13. 
    Rated M for Magnum liked post by Floundering Around On thread : .270 win load development - Which charge weight do you think?

    @ Rated M for Magnum Correct it is a hunting rifle. Probably 400 metres at the absolute max depending on the animal in the crosshairs. Will definitely sling some more lead to see if I can refine it.

    Liked On: 22-01-2024, 02:51 PM

14. 
    Rated M for Magnum liked post by Carbine On thread : Moving up in calibre - 300 Win, 300 WSM, 7mm RM or there?

    6 months ago i was in the same boat but decided to get a full seperate setup for long range stuff ended up with the exact setup i wanted as new condition for $2400 on trademe set up was worth just...

    Liked On: 18-01-2024, 09:53 PM

15. 
    Rated M for Magnum liked post by southernman On thread : 6mm Creedmoor vs 243

    This is not correct, if it is a factory 6mm Remington, its a 1-9 twist or there about, the 6mm Remington was first called a .244 Remington and was 1-12 twist and wont stabilize over about 90gr...

    Liked On: 08-01-2024, 06:51 PM

Page 2 of 27 First 12345678910111213141516 ... Last

• Jump to page: