rupert
Member

574 Likes

Page 23 of 39 First ... 910111213141516171819202122232425262728293031323334353637 ... Last

• Jump to page:

1. 
   rupert liked post by Seventenths On thread : Tahr hunting Rope

   I would be really careful with ropes as people tend to push limits in order to access country or recover an animal and that's when murphy shows up! No animal is worth it... if the animal isn't in...

   Liked On: 27-01-2023, 03:31 PM

2. 
   rupert liked post by Barry the hunter On thread : DOC not giving out private landowner contact details

   a suggestion - try to contact one of the Wild Animal Control staff at your local DOC office - many of the receptionists have very little knowledge of hunting areas no matter how friendly they are -...

   Liked On: 27-01-2023, 01:27 PM

3. 
   rupert liked post by Marty Henry On thread : Adventures in the world of 12 bore solids

   Casting up a load of .665 round balls before sending the mold to akaroa1 reminded me l had been meaning to load some 12 gauge with them. In my Brno 204, Winchester rifled slugs shoot into 3 inches...

   Liked On: 23-01-2023, 03:56 PM

4. 
   rupert liked post by Fssprecision On thread : When you can't get the parts

   Well sometimes you can't get old parts so you just have to make it from stock. This old Tikka had the bolt release missing and no parts were available so a few hours milling later and all working...

   Liked On: 17-01-2023, 06:02 PM

5. 
   rupert liked post by caberslash On thread : 7mm08 - Hornady 11 th edition 150 ELD-X Superformance Load data

   Since you lot turned me onto this powder (and made me buy some!), I thought I'd share this: 214687 214688 For anyone wondering, it's not a compressed load. Interesting to see that Hornady...

   Liked On: 16-01-2023, 01:11 PM

6. 
   rupert liked post by Tedz50 On thread : Slugs with Unique

   The following from Ballisticproducts.com. "Unique's burn rate is to fast for Lee slugs, unless you want reduced loads. There is no data using plastic wads & Lee Key drive slug & Unique powder,...

   Liked On: 13-01-2023, 09:10 AM

7. 
   rupert liked post by 38 South On thread : Over-torqued screws

   My interpretation is that the head of a socket head screw has separated from the shank, if you have been able to remove the shank from lower half of the ring it should simply be a matter of fitting a...

   Liked On: 07-01-2023, 11:30 AM

8. 
   rupert liked post by Hunter2 On thread : .22 Magnum Accuracy

   Hello RUMPY. Thank you for trying to help me post photos. I nearly managed it on my last attempt only to see one phot and lost my typed out reply to you. Hence I am trying again. Here goes.213557 ...

   Liked On: 03-01-2023, 05:46 PM

9. 
   rupert liked post by flock On thread : Bought new bino's...good move or bad?

   I splashed and bought the vortex fury HD 5000 ABs, so far very happy with them. Main feature you can set them up ballistically for the rifle you are using. Has a compass wind calulating set up, but...

   Liked On: 01-01-2023, 01:19 PM

10. 
    rupert liked post by 308 On thread : Cheap gunsafes

    Walking through Mitre10 Mega yesterday looking for a cheap deadlock I was mildly surprised to see gunsafes there so thought I'd put up a pic I can't vouch for how good they are but they look...

    Liked On: 01-01-2023, 10:19 AM

11. 
    rupert liked post by Wingman On thread : Quality "everlasting" .410 shells

    Before I even get started on this thread I would like to point out that Micky Duck was totally responsible fore sending me down this rabbit hole. I was quite happy shooting factory loaded .410 ammo...

    Liked On: 31-12-2022, 09:52 PM

12. 
    rupert liked post by Oldbloke On thread : Cast Lead Thread ?

    DIY BRINELL HARDNESS TESTER. ( BHN ) Just found this thread. As mentioned earlier there are a few ways to do this. Lee test kit. I haven't used this but reports suggest it works fine but a but...

    Liked On: 31-12-2022, 07:25 PM

13. 
    rupert liked post by Oldbloke On thread : Free reloading Manuals

    This has been available for a while but i no idea if it's been posted here before. https://marvinstuart.com/firearm/Manuals/Reloading/Reloading%20Manuals/

    Liked On: 28-12-2022, 08:09 PM

14. 
    rupert liked post by Moa Hunter On thread : Boots without the pu shit

    I am not a fan of expensive boots with Gortex or some other semi permeable membrane, cheap boots fine but with expensive ones, the membrane dies before the boots and whats left is a pair of dry...

    Liked On: 22-12-2022, 05:47 PM

15. 
    rupert liked post by hunt08 On thread : Boots without the pu shit

    After having my crisps boot shit them self's in the pu I was talking with the boot shop that I use & they went though the boots that said that these...

    Liked On: 22-12-2022, 01:59 AM

Page 23 of 39 First ... 910111213141516171819202122232425262728293031323334353637 ... Last

• Jump to page: