shooternz
Member

904 Likes

Page 2 of 61 First 1234567891011121314151652 ... Last

• Jump to page:

1. 
   shooternz liked post by Marty Henry On thread : 30-40 Krag load conundrums

   An old book tells me imr 4064 (ar2208) will do it all from 110 to 220 grains and the oldest adi book reckons 2206h. For 165s 37-42 gr 2208, 33-38 2206h is what I can find

   Liked On: 08-05-2023, 06:43 PM

2. 
   shooternz liked post by SmokeyJason On thread : Speer 30 grain TNT Green .224

   Ah if only. As I could use it in the 22 hornet.

   Liked On: 07-05-2023, 01:13 PM

3. 
   shooternz liked post by ChrisW On thread : 308 - short barrel loads for medium-long range

   The powder that gives the highest velocity in a long barrel will also give the highest velocity in a short barrel, so powder choice is the same as what you'd usually pick.

   Liked On: 28-04-2023, 07:15 PM

4. 
   shooternz liked post by XR500 On thread : No more powder

   ...Which aggressor? There's more than one.

   Liked On: 25-04-2023, 02:48 PM

5. 
   shooternz liked post by grandpamac On thread : Recommended Reloading Reading

   Greetings, Handloader Ammunition Reloading Journal put out by Wolf Publishing and Load Data dot com are good sources for reliable articles and data, together with the Hodgdons and ADI on line load...

   Liked On: 22-04-2023, 01:37 PM

6. 
   shooternz liked post by Friwi On thread : What 22-250 in a 1-8 twist.

   To go Semi factory 1in 8 twist, you have to buy two tikkas. 1 varmint one in 223 1 in 8 twist that you rechamber and use the bolt of a standard 22-250/ 308 bolt face. But then you end up with a...

   Liked On: 07-04-2023, 05:39 PM

7. 
   shooternz liked post by Morepork On thread : 303 wildcats??

   I have one, I made a few years ago, 35/303 I used a 35 Whelen reamer, it was reamed into the 303 case length, all work was done at True Flite, fitted red and green fibre optic open sights. I cut...

   Liked On: 06-03-2023, 10:20 AM

8. 
   shooternz liked post by Dermastor On thread : Moly for barrel?

   I don't believe it will work that well. I had a 7mm Rem Mag that copper fouled like crazy. I tried all sorts of moly barrel treatments and projectile coatings to no avail. It was very accurate, but...

   Liked On: 03-03-2023, 11:34 AM

9. 
   shooternz liked post by ebf On thread : Case lengthening when bump sizing

   Ok, so here is an experiment for you. Get a shoulder bump / body die that is correctly set up. After firing, size your case, but DO NOT trim it. Keep doing this for several iterations. At some...

   Liked On: 02-03-2023, 02:27 PM

10. 
    shooternz liked post by ebf On thread : Case lengthening when bump sizing

    Add to this that when you start using expander buttons in sizing dies things get even more complex. I don't like expanders at all. For shoulder bumping I either buy body dies, or make them by...

    Liked On: 02-03-2023, 02:26 PM

11. 
    shooternz liked post by Scout On thread : 303 Nitro Proofed

    May not be any load info on the rifle, just nice if it is & a lot of Older English rifles had such, larger cartridges does not mean higher pressure but I'm sure it has ample strength for any .303Brit...

    Liked On: 23-02-2023, 10:59 PM

12. 
    shooternz liked post by gundoc On thread : Dumb question about shooting

    The problem is subject to a steadily increasing error factor that increases exponentially. Bullet stability, velocity, wind, mirage, temperature variation, barrel harmonics, personal ability, etc....

    Liked On: 13-02-2023, 01:04 PM

13. 
    shooternz liked post by 199p On thread : Dumb question about shooting

    TBH Belmont has been some of the most constant ammo ive been able to get my hands on shooting well above its purchase price, Might just be it doesnt like the Sako loads just because its expensive...

    Liked On: 13-02-2023, 01:00 PM

14. 
    shooternz liked post by 7mmsaum On thread : Dumb question about shooting

    Get all the copper/ carbon out of your barrel first Try again

    Liked On: 13-02-2023, 12:55 PM

15. 
    shooternz liked post by Marty Henry On thread : The importance of Seating depths

    That's an impressive 2nd photo cluster of shots but Call me pedantic, in hunting terms does the difference between a 1 moa and .4 moa really matter? It obviously does in target shooting but in the...

    Liked On: 17-01-2023, 10:33 PM

Page 2 of 61 First 1234567891011121314151652 ... Last

• Jump to page: