zimmer
Member

1490 Likes

Page 24 of 100 First ... 101112131415161718192021222324252627282930313233343536373874 ... Last

• Jump to page:

1. 
   zimmer liked post by akaroa1 On thread : Who needs to add serial numbers in CHCH?

   I recently got my own Engraving Pantograph and have started on the firearms I have that don't have any serial numbers. With the right gear it's actually pretty easy. If there are a few guys...

   Liked On: 06-07-2023, 03:39 PM

2. 
   zimmer liked post by Micky Duck On thread : Primer question

   lets just say I have a polarfleece vest that looks like it was owned by a smoker.....

   Liked On: 05-07-2023, 09:04 PM

3. 
   zimmer liked post by johnd On thread : Primer question

   Might be time to resurect this thread from last year https://www.nzhuntingandshooting.co.nz/f10/primers-79872/

   Liked On: 05-07-2023, 08:26 PM

4. 
   zimmer liked post by RugerM77 On thread : Primer question

   In terms of your first question: I've tried but found the primers to be a bit loose when seating in another case. Second question: Probably not, but give it a go and let us know.

   Liked On: 04-07-2023, 09:04 PM

5. 
   zimmer liked post by gqhoon On thread : Tikka T3X barrel break-in

   I think this is the most significant aspect of breaking-in a barrel, in that it’s actually the chamber / bore transition that needs the attention. I’ll use abrasives on a patch and short-stroke this...

   Liked On: 04-07-2023, 09:46 AM

6. 
   zimmer liked post by shananah On thread : Reloading Equipment Covers

   They make the old 4 litre oil container with the handle & hole cut off tipped upside down over my Lyman Orange Crusher look a bit poor relly. :D

   Liked On: 04-07-2023, 09:45 AM

7. 
   zimmer liked post by Tech On thread : Recommended cleaning rods

   My Tipton Deluxe carbon fibre rod is still going strong after many years and countless number of barrels cleaned. I opted for a 44 inch rod which allows the jag to be out the muzzle while the handle...

   Liked On: 04-07-2023, 09:37 AM

8. 
   zimmer liked post by johnd On thread : Case Neck runout with redding type s bushing die

   At least it was a repeat not a contradiction.

   Liked On: 03-07-2023, 07:11 PM

9. 
   zimmer liked post by johnd On thread : Case Neck runout with redding type s bushing die

   I have gone back to a F/L Forster die and open up with Sinclair mandrel.

   Liked On: 03-07-2023, 06:13 PM

10. 
    zimmer liked post by Waimauku On thread : Case Neck runout with redding type s bushing die

    Both my redding dies with bushings ,comp & type s were the same. I have continued with the redding fl and instead of the 3-4 thou it's now more like 1.5. Haven't looked at bushing dies since....

    Liked On: 03-07-2023, 05:57 PM

11. 
    zimmer liked post by Ben Waimata On thread : Rules for a strong room (NOT for endorsed weapons)??

    My understanding is that if a deer is wandering across your garden, if you can get access to your loaded firearms fast enough to shoot it before it disappears then the security is inadequate :P :P :P

    Liked On: 03-07-2023, 03:31 PM

12. 
    zimmer liked post by Micky Duck On thread : Rules for a strong room (NOT for endorsed weapons)??

    weird as storing the 3 bits seperately has been the done thing for close to 40 years....well at least 35 since I got my first licence..about the same time as cabinets came in.... we as family...

    Liked On: 03-07-2023, 12:01 PM

13. 
    zimmer liked post by csmiffy On thread : Firearm Registry Data Questions and Answers

    zimmer quote from my email from the department. No as I got the permit in before hand, Im sweet. "When you receive your magazine and notify us by email, as per the Section 13 Regulation on your...

    Liked On: 01-07-2023, 03:56 PM

14. 
    zimmer liked post by Tasbay On thread : Useing the firearms register

    You add your own dreamt up serial number. I have a cannon with no serial so it will be my initials and a 1800s year.

    Liked On: 01-07-2023, 10:12 AM

15. 
    zimmer liked post by mikee On thread : NZDA requires FAL number

    The phrase "tilting at windmills" comes to mind reading this thread. If organisations require info like this for membership then you have a choice (its yours after all) to join.....or not. Common...

    Liked On: 28-06-2023, 02:06 PM

Page 24 of 100 First ... 101112131415161718192021222324252627282930313233343536373874 ... Last

• Jump to page: