Thread: 300 Rum Brass Cases

Originally Posted by baldbob

5psi is safe

Not in this chamber its not.


Sent from my GT-S5360T using Tapatalk 2

Originally Posted by baldbob

5psi is safe

Some of the pressure you relieved in my truck last month would exceed 20psi at least. Foul substance, it was, as well.

Originally Posted by veitnamcam

Not in this chamber its not.
Attachment 9568

Sent from my GT-S5360T using Tapatalk 2

What is that VC?

Originally Posted by BRADS

What is that VC?

That was wee cammys brekkie

Originally Posted by R93

Some of the pressure you relieved in my truck last month would exceed 20psi at least. Foul substance, it was, as well.

That was coming from the back seat!!!! Pppllleeaaassseeee!!!!

Originally Posted by baldbob

That was wee cammys brekkie

That would hold a lot of porridge

I won't say anymore than it is /was a paint tank.

Sent from my GT-S5360T using Tapatalk 2

Bite the said tongue. ...

Originally Posted by tui_man2

this thread is bit fucked now an away from over loaded brass.............nice work facts are hidden.............again

Ah this thread was never about overloaded brass?

You and Luke made it that and then you posted some numbers and pictures to prove what exactly?



Sent from my GT-S5360T using Tapatalk 2

I'm with Cam. Lost like everyone else since your 1st post LOL

Originally Posted by veitnamcam

Ah this thread was never about overloaded brass?

You and Luke made it that and then you posted some numbers and pictures to prove what exactly?



Sent from my GT-S5360T using Tapatalk 2

Again. . . .
Primer pockets don't loosen themselves
Harder brass is trying to hide it. . . . .

I posted someone's pet load. . . . .
then posted ways around high pressure to make a fast safe load. . . . . Simple to me? No


Sent from my GT-I9300T using Tapatalk 2

Originally Posted by tui_man2

Again. . . .
Primer pockets don't loosen themselves
Harder brass is trying to hide it. . . . .

I posted someone's pet load. . . . .
then posted ways around high pressure to make a fast safe load. . . . . Simple to me? No


Sent from my GT-I9300T using Tapatalk 2

Na you didn't you posted two loads with no pressure data and didn't state if they were any chamber powder brass primer changes just this one is more powder and less pressure.

I can put 52 gr of 2208 in a 308 case with no pressure signs but i sure as Fuck wouldn't even try that with n140 both of which are the same proposed burn rate .



Sent from my GT-S5360T using Tapatalk 2

Ie you didn't show ways around anything at all

Sent from my GT-S5360T using Tapatalk 2

Originally Posted by veitnamcam

Na you didn't you posted two loads with no pressure data and didn't state if they were any chamber powder brass primer changes just this one is more powder and less pressure.

I can put 52 gr of 2208 in a 308 case with no pressure signs but i sure as Fuck wouldn't even try that with n140 both of which are the same proposed burn rate .



Sent from my GT-S5360T using Tapatalk 2

Originally Posted by tui_man2

For sake of it pet load was 96gr, 2225, 215 primer, otm seated at 3.97"

New load is same but 100gr an 4.05"

There i said it.......in the first post

SAME primer
SAME cases
SAME powder
SAME projectile
MORE powder

So where did the excuess pressure go?
Why would i tell everyone the little bits i done to reduce the pressure?

I showed everything that was needed................

My RUM ended up with 100+ faster and 5 more grains in it for less indicated pressure on same brass