Thread: Various Knives

Originally Posted by Von Gruff Knives

Cold working destroys steel so no you cant move metal into different shapes without heat and enough heat (red at least) so it will move under the hammer without cracking so what you contemplate would ruin the blades. It is the heat treating of good carbon steel that makes them take and hold an edge and a correctly heat treated carbon steel blade will hold an edge but still be reasonably easy to keep sharp.

For me this is all the curve that a skinning knife should have and the way I worked toward making then since 1968 when I was given an old green river skinner with the big upswept blade to kill a few sheep on the high country station I went when I left school school. Hated the design and that was when I started critical analysis of knife design and working on better (for my use) shapes in both blade and handle for easy and safe use and handling.

well sometimes I do actually listen (my teachers would be amazed to read that) and took what you have said onboard...I did something less drastic..I sliced a piece off rear of swept skinning bade, made rear edge almost parrallel with handle... gave knife a decent point by doing so ,not having as much blade up above centreline is much better for me...really happy with end result and knife is nice to use so will GET used again now.
thankyou for the advice.

Originally Posted by Micky Duck

question for you...been pondering this all day.
Ive got two if not three old wooden handled skinning knives possibly green river possibly ex freezing works....very old and very easy to get and keep sharp..only issue I have is not a fan at all of curved skinning blades....how hard would it be/it it feasable/possible to heat and reshape blade to straight??? without having to go whole hog and heat to red and beat them to pulp and start again???

Another thing to think about is reshaping the blades to take some of the big upsweep off them. Careful grinding to minimise heat and you can do a great deal with an old knife that has good steel by re-shaping them. Not hard to do at all.

More ready to go with a General purpose kitchen and pairing knife in NitroV with spilled acrylic as a gift for a friend.
An EDC with curly eucalyptus over 1084 blade in stamped sheath with attached honing steel. The customer wanted my name engraved with the NuZ being the Czech way of spelling knives and with the N and Z being capitalised reinforcing its NZ made origin.
And for a repeat customer an Euro kitchen set in NitroV and a General purpose Field knife in 1084 HC, all with Totora over brass.

A Wapiti Hunter for a very big man so had to make the handle a 1/2 in longer than normal to suit his hands. A nice set of spalted Hackberry scales with snake knot lanyard over curve backed buffalo horn bolster on the 3/16 1075 blade and carried in a closed top sheath.

Picked up quite a bit of walnut from custom rifle stock blanks on a recent trip away and have spent an afternoon cutting it into knife handle blocks. Majority 60-70mm x 35mm x 130mm with a few at 60 x 30 x 130. Hope to get it all over the disc sander and ready to offer for sale soon.

The Wapiti Hunter with Tasmanian Backwood over curve backed brass bolters on the 5 inch 1075 HC blade in a closed top sheath was a rush order for a birthday gift this sunday.
A new addition to the pattern board is the #2 Bushcraft knife. It has a Koa handle on the 1075 blade with heavy jimping and a lanyard in the closed top sheath. The original Bushcraft Hunter I offered has a 3 3/4 in x 1 inch blade with full scandi grind where the #2 Bushcraft knife has a 4 3/4 x 1 1/4 inch blade with a low saber grind and shot=rt secondary bevel.

Originally Posted by Von Gruff Knives

The Wapiti Hunter with Tasmanian Backwood over curve backed brass bolters on the 5 inch 1075 HC blade in a closed top sheath was a rush order for a birthday gift this sunday.
A new addition to the pattern board is the #2 Bushcraft knife. It has a Koa handle on the 1075 blade with heavy jimping and a lanyard in the closed top sheath. The original Bushcraft Hunter I offered has a 3 3/4 in x 1 inch blade with full scandi grind where the #2 Bushcraft knife has a 4 3/4 x 1 1/4 inch blade with a low saber grind and shot=rt secondary bevel.

How much does a knife in the design of the wapiti hunter as shown above cost, roughly? Got to have something to save towards haha. What a work of art, yet practical!

Originally Posted by JoelA

How much does a knife in the design of the wapiti hunter as shown above cost, roughly? Got to have something to save towards haha. What a work of art, yet practical!

PM sent.

A 4x4 Hunter with african Olivewood over curve backed buffalo horn on the stone washed 1084 blade in an edge stamped closed top sheath.

like it very much indeed...

A General purpose field knife with some of the very nice walnut on the 1084 blade in simply pouch sheath, and a pretty little Bird and Trout knife with Tasmanian Blackwood on the NitroV SS blade in a closed top sheath.

Prefer the shape of that bird/trout over the one on your website.
Whatever your reason for the mod, it’s a good call imho.
Love your work

Originally Posted by Boner

Prefer the shape of that bird/trout over the one on your website.
Whatever your reason for the mod, it’s a good call imho.
Love your work

Thanks for the comment Boner, but there was no mod to the design. I know the pic on the website may appear to have more upsweep on the blade but the same steel pattern was used for both these and other B & T knives made.

A couple of knives away with a plain Chamois Hunter with Totora and a Pig Sticker with aged Giraffe bone.

This Lion knife and Safari knife in 1075 with yellow cedar burl ready to ship in the morning.